This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-29. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | Samsung measurement source — RF30BB6200_V12.pdf groveappliance.com | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Product Dimensions width with hinges and doors.Open original source ↗ All retained supporting links
Why this value was usedProduct Dimensions width with hinges and doors. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.875 in | ✓ Verified — retained secondary source | Samsung measurement source — RF30BB6200_V12.pdf groveappliance.com | Page 2 | |
Value used by ExactFit68.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Product Dimensions height without hinges and door.Open original source ↗ All retained supporting links
Why this value was usedProduct Dimensions height without hinges and door. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 70 in | ✓ Verified — exact model | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit70 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Product Dimensions height with hinges and doors.Open original source ↗ All retained supporting links
Why this value was usedProduct Dimensions height with hinges and doors. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29.375 in | ✓ Verified — retained secondary source | Samsung measurement source — RF30BB6200_V12.pdf groveappliance.com | Page 2 | |
Value used by ExactFit29.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Product Dimensions depth without hinges and door.Open original source ↗ All retained supporting links
Why this value was usedProduct Dimensions depth without hinges and door. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34.25 in | ✓ Verified — retained secondary source | Samsung measurement source — RF30BB6200_V12.pdf groveappliance.com | Page 2 | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Product Dimensions closed depth without a projecting handle.Open original source ↗ All retained supporting links
Why this value was usedProduct Dimensions closed depth without a projecting handle. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 34.25 in | ✓ Verified — retained secondary source | Samsung measurement source — RF30BB6200_V12.pdf amdirectappliances.com | Page 2 | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Product Dimensions closed maximum depth including the shown handle configuration.Open original source ↗ All retained supporting links
Why this value was usedProduct Dimensions closed maximum depth including the shown handle configuration. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.5 in | ✓ Verified — exact model | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit48.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Visually labeled 90-degree front-to-back envelope in the dimension drawing.Open original source ↗ All retained supporting links
Why this value was usedVisually labeled 90-degree front-to-back envelope in the dimension drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36.5 in | ✓ Verified — retained secondary source · Calculated/inferred | Samsung measurement source — RF30BB6200_V12.pdf groveappliance.com | Page 2 | |
Value used by ExactFit36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.75 + 2 * 0.375 Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Closed product width plus the explicitly required clearance at each side.Open original source ↗ All retained supporting links
Why this value was usedClosed product width plus the explicitly required clearance at each side. Calculation or inference: 35.75 + 2 * 0.375. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.375 in | ✓ Verified — exact model · Calculated/inferred | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 70 + 0.375 Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Height with hinges plus the explicitly required top clearance.Open original source ↗ All retained supporting links
Why this value was usedHeight with hinges plus the explicitly required top clearance. Calculation or inference: 70 + 0.375. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 30.375 in | ✓ Verified — exact model · Calculated/inferred | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit30.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.375 + 1 Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Case depth without door plus the explicitly required rear clearance.Open original source ↗ All retained supporting links
Why this value was usedCase depth without door plus the explicitly required rear clearance. Calculation or inference: 29.375 + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.375 in | ✓ Verified — exact model | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf The document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top."Open original source ↗ All retained supporting links
Why this value was usedThe document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top." Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.375 in | ✓ Verified — exact model | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf The document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top."Open original source ↗ All retained supporting links
Why this value was usedThe document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top." Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.375 in | ✓ Verified — exact model | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Allow 0.375 in minimum clearance at sides and top.Open original source ↗ All retained supporting links
Why this value was usedAllow 0.375 in minimum clearance at sides and top. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — exact model | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Allow 1 in minimum clearance at rear.Open original source ↗ All retained supporting links
Why this value was usedAllow 1 in minimum clearance at rear. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.5 in | ✓ Verified — exact model | Samsung measurement source — RF30BB6200_V12.pdf Samsung | Page 2 | |
Value used by ExactFit2.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 2.5 in clearance on hinge side when installing next to a wall.Open original source ↗ All retained supporting links
Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 2.5 in clearance on hinge side when installing next to a wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | Samsung measurement source — RF30BB6200_V12.pdf groveappliance.com | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RF30BB6200_V12.pdf Visually labeled cabinet/product width on the dimension drawing.Open original source ↗ All retained supporting links
Why this value was usedVisually labeled cabinet/product width on the dimension drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
groveappliance.com · Web source · secondary model/source
Model numbers covered: RF30BB6200QLAA. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
16 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.