Measurement evidence for Samsung RF29DB9900QDAA

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 105583998.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-09-04

Page 22 RF29DB****** Width B: 35 7/8" (912 mm).

Why this value was used

Page 22 RF29DB****** Width B: 35 7/8" (912 mm).

Other evidence found

• 35.87 in — superseded

  www.cameronfurnitureandappliance.com; location not retained. Model scope: not separately recorded. Raw value: Exact-model table: Width 35.87 inches.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 105583998.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-09-04

Page 22 labels C as Height without hinge; RF29DB****** C: 70 3/4".

Why this value was used

Page 22 labels C as Height without hinge; RF29DB****** C: 70 3/4".

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105583978.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

Clearance table for RF29DB******: A depth 34 1/4 in (869 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). The stored field holds the appliance's highest point, the overall height D (owner rule).

Why this value was used

Clearance table for RF29DB******: A depth 34 1/4 in (869 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). The stored field holds the appliance's highest point, the overall height D (owner rule).

Other evidence found

• 72 in — superseded

  Document 105583998.pdf; page 22. Model scope: not separately recorded. Raw value: Page 22 labels E as Height with hinge; RF29DB****** E: 72".. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 105583998.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Page 23 side-view dimension 05 for RF29D*******: 29 3/8" (748 mm).

Why this value was used

Page 23 side-view dimension 05 for RF29D*******: 29 3/8" (748 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Recessed-handle model: overall closed depth equals handleless depth

Confidence label: medium.

Primary evidence

Samsung measurement source — 105583998.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-09-04

Page 22 RF29DB****** Depth A: 34 1/4" (869 mm); recessed-handle design.

Why this value was used

Page 22 RF29DB****** Depth A: 34 1/4" (869 mm); recessed-handle design. Calculation or inference: Recessed-handle model: overall closed depth equals handleless depth.

Other evidence found

• 90 in — superseded

  alabamaapplianceoutlet.com; location not retained. Model scope: not separately recorded. Raw value: depth without handles: Depth with Door Open 90°. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 854725-samsung-rf29db9900qdaa
www.cameronfurnitureandappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 35.87 inch(es). Height (With Hinge), 73 inch(es). Overall Depth, 34.25 inch(es). Depth (
Reviewed: 2026-09-04

35.87 inch(es). Height (With Hinge), 73 inch(es). Overall Depth, 34.25 inch(es). Depth (

Why this value was used

35.87 inch(es). Height (With Hinge), 73 inch(es). Overall Depth, 34.25 inch(es). Depth (

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.5 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RF29DB9) from RF29DB9600QLAA

Confidence label: medium.

Primary evidence

Samsung measurement source — french-door-beverage-center-29-cu-ft-stainless-steel-rf29db9600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 48.5 in from RF29DB9600QLAA; at least three populated dimensions match
Reviewed: 2026-09-04

Unanimous same-platform value 48.5 in from RF29DB9600QLAA; at least three populated dimensions match and none conflict. Donor evidence: Depth with doors open at 90º 48 1/2 inches

Why this value was used

Unanimous same-platform value 48.5 in from RF29DB9600QLAA; at least three populated dimensions match and none conflict. Donor evidence: Depth with doors open at 90º 48 1/2 inches Calculation or inference: Samsung platform-family propagation (RF29DB9) from RF29DB9600QLAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.62 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.87 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — 854725-samsung-rf29db9900qdaa + side gap from the maker's document
www.cameronfurnitureandappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.62 in from product width 35.87 in and explicit 0.375 in clearance o
Reviewed: 2026-09-04

Derived minimum opening width 36.62 in from product width 35.87 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.62 in from product width 35.87 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.87 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Recalculated 2026-10-04 with the stored formula from current inputs: max(height_case_in,height_hinge
Reviewed: 2026-10-03

Recalculated 2026-10-04 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 70.75, height_hinge_in = 73, top_clearance_in = 0.375 = 73.375 in (previously 72.375 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 70.75, height_hinge_in = 73, top_clearance_in = 0.375 = 73.375 in (previously 72.375 in). Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

• 72.375 in — superseded

  The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 72 in appliance endpoint + 0.375 in clearance = 72.375 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 29.375 in appliance endpoint + 2 in clearance = 31.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 29.375 in appliance endpoint + 2 in clearance = 31.375 in.

Why this value was used

Samsung installation envelope: 29.375 in appliance endpoint + 2 in clearance = 31.375 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top
Reviewed: 2026-09-05

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Why this value was used

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow 2" minimum clearance at rear
Reviewed: 2026-09-05

Cached exact-model result: Allow 2" minimum clearance at rear

Why this value was used

Cached exact-model result: Allow 2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700_2026-10-30.pdf
Samsung · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Samsung Will-it-fit sheet "MODEL RF29DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF29DB9700, the same fridge as RF29DB9900 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Why this value was used

Samsung Will-it-fit sheet "MODEL RF29DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF29DB9700, the same fridge as RF29DB9900 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

11.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF29DB9900QD_2026-10-30.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-30

Samsung RF29DB9900 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Why this value was used

Samsung RF29DB9900 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: RF29DB family overall width mapped to case width

Confidence label: medium.

Primary evidence

Samsung measurement source — 105583998.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-09-04

Page 22 RF29DB****** Width B: 35 7/8" (912 mm).

Why this value was used

Page 22 RF29DB****** Width B: 35 7/8" (912 mm). Calculation or inference: RF29DB family overall width mapped to case width.

Other evidence found

• 35.87 in — superseded

  www.cameronfurnitureandappliance.com; location not retained. Model scope: not separately recorded. Raw value: Low-confidence same-appliance width mapping: case_width_in=35.87 in from width_doors_closed_in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.