Measurement evidence for Samsung RF29DB9600QLAA

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — french-door-beverage-center-29-cu-ft-stainless-steel-rf29db9600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Net Width (inch) 35.875 inch
Reviewed: 2026-09-04

Net Width (inch) 35.875 inch

Why this value was used

Net Width (inch) 35.875 inch

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-4-door-flex-refrigerator-29-cu-ft-with-beverage-center-in-stainless-steel-sku-rf29db9600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height without Hinge = 70.75 in | H) x 36.25" (D) Net Depth with Door Handle 34.25" Net Height with
Reviewed: 2026-09-04

Height without Hinge = 70.75 in | H) x 36.25" (D) Net Depth with Door Handle 34.25" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 34.25" Depth without Door (in) 29 3/8" Width 35 7/8"

Why this value was used

Height without Hinge = 70.75 in | H) x 36.25" (D) Net Depth with Door Handle 34.25" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 34.25" Depth without Door (in) 29 3/8" Width 35 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29db9600qlaa
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 9 | | Net Depth with Door Handle | 34.25" | | Net Height with Hinge | 73" | | Net Height without Hin
Reviewed: 2026-09-04

9 | | Net Depth with Door Handle | 34.25" | | Net Height with Hinge | 73" | | Net Height without Hinge | 70.75" | | Depth w

Why this value was used

9 | | Net Depth with Door Handle | 34.25" | | Net Height with Hinge | 73" | | Net Height without Hinge | 70.75" | | Depth w

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-4-door-flex-refrigerator-29-cu-ft-with-beverage-center-in-stainless-steel-sku-rf29db9600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Depth without Door 29 3/8 in; depth without handle is separately 34.25 in
Reviewed: 2026-09-04

Official exact-model page: Depth without Door 29 3/8 in; depth without handle is separately 34.25 in.

Why this value was used

Official exact-model page: Depth without Door 29 3/8 in; depth without handle is separately 34.25 in.

Other evidence found

• 34.25 in — superseded

  appliancehomestore.com; location not retained. Model scope: not separately recorded. Raw value: 73" | | Net Height without Hinge | 70.75" | | Net Depth w/o Door Handle | 34.25" | | Depth without Door (in) | 29 3/8" | | Width |. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-4-door-flex-refrigerator-29-cu-ft-with-beverage-center-in-stainless-steel-sku-rf29db9600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth w/o Door Handle: 34.25 in | oor Handle 34.25" Net Height with Hinge 73" Net Height without Hin
Reviewed: 2026-09-04

Depth w/o Door Handle: 34.25 in | oor Handle 34.25" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 34.25" Depth without Door (in) 29 3/8" Width 35 7/8" Height 73" Height (decimal) 73 Wi

Why this value was used

Depth w/o Door Handle: 34.25 in | oor Handle 34.25" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 34.25" Depth without Door (in) 29 3/8" Width 35 7/8" Height 73" Height (decimal) 73 Wi

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-4-door-flex-refrigerator-29-cu-ft-with-beverage-center-in-stainless-steel-sku-rf29db9600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle: 34.25 in | (H) x 29 3/8" (D) Shipping Dimensions 38.25" (W) x 78.625" (H) x
Reviewed: 2026-09-04

Depth with Door Handle: 34.25 in | (H) x 29 3/8" (D) Shipping Dimensions 38.25" (W) x 78.625" (H) x 36.25" (D) Net Depth with Door Handle 34.25" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Ha

Why this value was used

Depth with Door Handle: 34.25 in | (H) x 29 3/8" (D) Shipping Dimensions 38.25" (W) x 78.625" (H) x 36.25" (D) Net Depth with Door Handle 34.25" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Ha

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — french-door-beverage-center-29-cu-ft-stainless-steel-rf29db9600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with doors open at 90º 48 1/2 inches
Reviewed: 2026-09-04

Depth with doors open at 90º 48 1/2 inches

Why this value was used

Depth with doors open at 90º 48 1/2 inches

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.625

Confidence label: high.

Calculation inputs: Overall width; Left-side ventilation clearance;

Primary evidence

Samsung measurement source — RF29DB9600QL_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearan
Reviewed: 2026-09-18

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.625 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged.

Why this value was used

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.625 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged. Calculation or inference: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.625.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — RF29DB9600_V3.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 73 in appliance endpoint + 0.375 in clearance = 73.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 73 in appliance endpoint + 0.375 in clearance = 73.375 in.

Why this value was used

Samsung installation envelope: 73 in appliance endpoint + 0.375 in clearance = 73.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — RF29DB9600QL_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF29DB9600_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF29DB9600_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF29DB9600_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top
Reviewed: 2026-09-05

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Why this value was used

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF29DB9600QL_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 2” minimum clearance at rear
Reviewed: 2026-09-05

2” minimum clearance at rear

Why this value was used

2” minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF29DB9700_2026-10-30.pdf
Samsung · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Samsung Will-it-fit sheet "MODEL RF29DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF29DB9700, the same fridge as RF29DB9600 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Why this value was used

Samsung Will-it-fit sheet "MODEL RF29DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF29DB9700, the same fridge as RF29DB9600 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

11.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF29DB9600QL_2026-10-30.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-30

Samsung RF29DB9600 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Why this value was used

Samsung RF29DB9600 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF29DB9600QL_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions without hinges and doors: width 35 7/8 in
Reviewed: 2026-09-04

Dimensions without hinges and doors: width 35 7/8 in

Why this value was used

Dimensions without hinges and doors: width 35 7/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.