This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-15. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Value used by ExactFit
35.75 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4" Reviewed: 2026-09-09
Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8"
Value used by ExactFit
68.875 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8" Reviewed: 2026-09-09
Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8"
Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8"
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Value used by ExactFit
70 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4" Reviewed: 2026-09-09
Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8"
Value used by ExactFit
29.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8" Reviewed: 2026-09-09
Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8"
Dimensions (WxHxD without hinges and door): 35 3/4" x 68 7/8" x 29 3/8"
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Value used by ExactFit
34.25 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4" Reviewed: 2026-09-09
Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-09
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: 48 1/2" Reviewed: 2026-09-09
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — WillitFit_RF29BB8600_V2.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
{"calculation": "70.0 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/sources/Samsung/RF29BB8600QLAA/RF29BB8600_V9-specification.pdf", "page": "PDF page 2, Product Dimensions tuple and diagram label D", "raw": "Dimensions (WxHxD with hinges and doors): 35 3/4\" x 70\" x 34 1/4\"", "source_url": "https://image-us.samsung.com/SamsungUS/home/home-appliances/pdf/RF29BB8600_V9.pdf", "value_in": 70.0}, {"cache_path": "data/sources/Samsung/RF29BB8600QLAA/DA68-04402B-01-user-manual.pdf", "page": "PDF page 20, RF29BB8***** table, dimension D", "raw": "D 70\" (1778 mm)", "source_url": "https://org.downloadcenter.samsung.com/downloadfile/ContentsFile.aspx?CDSite=UNI_LATIN_EN&OriginYN=N&ModelType=N&ModelName=RF29BB8600QL&CttFileID=11398930&CDCttType=UM&VPath=UM%2F202604%2F20260429143959486%2FDA68-04402B-01_FDR_RF8000B_EN_260422.pdf", "value_in": 70.0}], "top_clearance_in": [{"cache_path": "data/sources/Samsung/RF29BB8600QLAA/RF29BB8600_V9-specification.pdf", "page": "PDF page 2, Installation Specifications item 4", "raw": "Allow a 3/8\" minimum clearance at sides and top for ease of installation.", "source_url": "https://image-us.samsung.com/SamsungUS/home/home-appliances/pdf/RF29BB8600_V9.pdf", "value_in": 0.375}]}, "result_in": 70.375} Calculation or inference: 70.0 + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/Samsung/RF29BB8600QLAA/RF29BB8600_V9-specification.pdf", "page": "PDF page 2, Product Dimensions tuple without hinges and door", "raw": "Dimensions (WxHxD without hinges and door): 35 3/4\" x 68 7/8\" x 29 3/8\"", "source_url": "https://image-us.samsung.com/SamsungUS/home/home-appliances/pdf/RF29BB8600_V9.pdf", "value_in": 29.375}, {"cache_path": "data/sources/Samsung/RF29BB8600QLAA/DA68-04402B-01-user-manual.pdf", "page": "PDF page 21, RF29BB8***** table, dimension 05", "raw": "05 29 3/8\" (748 mm)", "source_url": "https://org.downloadcenter.samsung.com/downloadfile/ContentsFile.aspx?CDSite=UNI_LATIN_EN&OriginYN=N&ModelType=N&ModelName=RF29BB8600QL&CttFileID=11398930&CDCttType=UM&VPath=UM%2F202604%2F20260429143959486%2FDA68-04402B-01_FDR_RF8000B_EN_260422.pdf", "value_in": 29.375}], "rear_clearance_in": [{"cache_path": "data/sources/Samsung/RF29BB8600QLAA/RF29BB8600_V9-specification.pdf", "page": "PDF page 2, Installation Specifications item 4", "raw": "Allow 1\" minimum clearance at rear for proper air circulation and water/electrical connections.", "source_url": "https://image-us.samsung.com/SamsungUS/home/home-appliances/pdf/RF29BB8600_V9.pdf", "value_in": 1.0}]}, "result_in": 30.375} Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow a 3/8" minimum clearance at sides and top for ease of installation.
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Allow a 3/8" minimum clearance at sides and top for ease of installation. Reviewed: 2026-09-09
Allow a 3/8" minimum clearance at sides and top for ease of installation.
Allow a 3/8" minimum clearance at sides and top for ease of installation.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow a 3/8" minimum clearance at sides and top for ease of installation.
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Allow a 3/8" minimum clearance at sides and top for ease of installation. Reviewed: 2026-09-09
Allow a 3/8" minimum clearance at sides and top for ease of installation.
Allow a 3/8" minimum clearance at sides and top for ease of installation.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow a 3/8" minimum clearance at sides and top for ease of installation.
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Allow a 3/8" minimum clearance at sides and top for ease of installation. Reviewed: 2026-09-09
Allow a 3/8" minimum clearance at sides and top for ease of installation.
Allow a 3/8" minimum clearance at sides and top for ease of installation.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow 1" minimum clearance at rear for proper air circulation and water/electrical connections.
Value used by ExactFit
1 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Allow 1" minimum clearance at rear for proper air circulation and water/electrical connections. Reviewed: 2026-09-09
Allow 1" minimum clearance at rear for proper air circulation and water/electrical connections.
Allow 1" minimum clearance at rear for proper air circulation and water/electrical connections.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — WillitFit_RF29BB8600_V2.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-15
Will-it-fit sheet "MODEL RF29BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Will-it-fit sheet "MODEL RF29BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Other evidence found
2.5 in — superseded
Document RF29BB8600_V9-specification.pdf; location not retained. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 2.5" of clearance on hinge side of refrigerator when installing next to a wall where handle may make contact.. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Value used by ExactFit
35.75 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF29BB8600_V9-specification.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4" Reviewed: 2026-09-09
Dimensions (WxHxD with hinges and doors): 35 3/4" x 70" x 34 1/4"
Selected: 3.75 in. Earlier retained values: 2.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Will-it-fit sheet "MODEL RF29BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Model numbers covered: RF29BB8600QLAA. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
14 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-15. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
