Measurement evidence for Samsung RF29BB860012AA

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29bb860012aa.html
www.4brothersappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Plain exact-model specification row: Width = 35.75 in | ft.) with ... 4-Door French Door Refrigerat
Reviewed: 2026-09-04

Plain exact-model specification row: Width = 35.75 in | ft.) with ... 4-Door French Door Refrigerator. Extra-large capacity 4-Door French Door Refrigerator. Width: 35.75" Height: 70" Depth: 34.25" Energy Star Rated: Yes

Why this value was used

Plain exact-model specification row: Width = 35.75 in | ft.) with ... 4-Door French Door Refrigerator. Extra-large capacity 4-Door French Door Refrigerator. Width: 35.75" Height: 70" Depth: 34.25" Energy Star Rated: Yes

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29bb860012aa
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Height without Hinge = 68.875 in | imensions 38 1/4" (W) x 76 3/4"
Reviewed: 2026-09-04

Exact-model cached specification: Height without Hinge = 68.875 in | imensions 38 1/4" (W) x 76 3/4" (H) x 36 1/4" (D) Net Height with Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 34 1/4" Depth without Door (in) 29 3/8" Width 35 3/4"

Why this value was used

Exact-model cached specification: Height without Hinge = 68.875 in | imensions 38 1/4" (W) x 76 3/4" (H) x 36 1/4" (D) Net Height with Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 34 1/4" Depth without Door (in) 29 3/8" Width 35 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29bb860012aa
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 396.8 | | Shipping Weight (lbs.) | 396.8 | | Net Height with Hinge | 70" | | Net Height without Hing
Reviewed: 2026-09-04

396.8 | | Shipping Weight (lbs.) | 396.8 | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Depth

Why this value was used

396.8 | | Shipping Weight (lbs.) | 396.8 | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Depth

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29bb860012aa
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Depth without Door = 29.375 in | th Hinge 70" Net Height without H
Reviewed: 2026-09-04

Exact-model cached specification: Depth without Door = 29.375 in | th Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 34 1/4" Depth without Door (in) 29 3/8" Width 35 3/4" Height 70" Product Dimensions without Hinges and Door 35 6/8" x 6

Why this value was used

Exact-model cached specification: Depth without Door = 29.375 in | th Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 34 1/4" Depth without Door (in) 29 3/8" Width 35 3/4" Height 70" Product Dimensions without Hinges and Door 35 6/8" x 6

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29bb860012aa
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached Samsung specification: depth_less_handles_in = 34.25 in; source_id=64941
Reviewed: 2026-09-04

Exact-model cached Samsung specification: depth_less_handles_in = 34.25 in; source_id=64941

Why this value was used

Exact-model cached Samsung specification: depth_less_handles_in = 34.25 in; source_id=64941

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29bb860012aa
amdirectappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle = 34.25 in | ; Product Dimensions without Hinges and Door, 35 6/8" x 68 7/8"
Reviewed: 2026-09-04

Depth with Door Handle = 34.25 in | ; Product Dimensions without Hinges and Door, 35 6/8" x 68 7/8" x 29 3/8" ; Net Depth with Door Handle, 34 1/4" ; Height (decimal), 70.

Why this value was used

Depth with Door Handle = 34.25 in | ; Product Dimensions without Hinges and Door, 35 6/8" x 68 7/8" x 29 3/8" ; Net Depth with Door Handle, 34 1/4" ; Height (decimal), 70.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.5 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-brand product-class chassis propagation from RF30BB660012AA

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rf30bb660012aa
www.shopappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Medium-confidence chassis inference from RF30BB660012AA. Donors unanimously report depth_doors_open_
Reviewed: 2026-09-04

Medium-confidence chassis inference from RF30BB660012AA. Donors unanimously report depth_doors_open_90_in=48.5 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: Depth with Door Opened at 90 Degrees = 48.5 in | | 35 3/4" | | Depth | | Depth | 34 1/4" | | Depth without Handles | 34 1/4" | | Depth with Door Opened at 90 Degrees | 48 1/2" | | Counter-Depth | No | | Height | | Height | 70" | | Height without Hinges |

Why this value was used

Medium-confidence chassis inference from RF30BB660012AA. Donors unanimously report depth_doors_open_90_in=48.5 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: Depth with Door Opened at 90 Degrees = 48.5 in | | 35 3/4" | | Depth | | Depth | 34 1/4" | | Depth without Handles | 34 1/4" | | Depth with Door Opened at 90 Degrees | 48 1/2" | | Counter-Depth | No | | Height | | Height | 70" | | Height without Hinges | Calculation or inference: same-brand product-class chassis propagation from RF30BB660012AA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — rf29bb860012aa.html + side gap from the maker's document
www.4brothersappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — 62060280-manufacturer's-brochure.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance 0.375 in.

Why this value was used

Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-autofill-pitcher-30-cu-ft-silver-rf30bb6200qlaa
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 29.375 in plus propagated rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.375 in plus propagated rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 29.375 in plus propagated rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 62060280-manufacturer's-brochure.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung RF29BB/RF30BB Bespoke brochure (lists RF29BB86004MAA, RF30BB620012AA, RF30BB660012AA, RF30BB
Reviewed: 2026-10-29

Samsung RF29BB/RF30BB Bespoke brochure (lists RF29BB86004MAA, RF30BB620012AA, RF30BB660012AA, RF30BB69006MAA and the same-chassis models): "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Why this value was used

Samsung RF29BB/RF30BB Bespoke brochure (lists RF29BB86004MAA, RF30BB620012AA, RF30BB660012AA, RF30BB69006MAA and the same-chassis models): "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 62060280-manufacturer's-brochure.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung RF29BB/RF30BB Bespoke brochure (lists RF29BB86004MAA, RF30BB620012AA, RF30BB660012AA, RF30BB
Reviewed: 2026-10-29

Samsung RF29BB/RF30BB Bespoke brochure (lists RF29BB86004MAA, RF30BB620012AA, RF30BB660012AA, RF30BB69006MAA and the same-chassis models): "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Why this value was used

Samsung RF29BB/RF30BB Bespoke brochure (lists RF29BB86004MAA, RF30BB620012AA, RF30BB660012AA, RF30BB69006MAA and the same-chassis models): "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF30BB620012AA

Confidence label: medium.

Primary evidence

Samsung measurement source — 62060280-manufacturer's-brochure.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB620012AA; original e
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB620012AA; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 1 copy/copies, 1 domain(s), official=False; no contrary parsed value.

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB620012AA; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 1 copy/copies, 1 domain(s), official=False; no contrary parsed value. Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF30BB620012AA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF30BB6200QLAA

Confidence label: medium.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-autofill-pitcher-30-cu-ft-silver-rf30bb6200qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB6200QLAA; original e
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB6200QLAA; original evidence: 2 inches of space in the back

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB6200QLAA; original evidence: 2 inches of space in the back Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF30BB6200QLAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF29BB8600_V2.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-25

Same Samsung base model as RF29BB8600QLAA (identical stored dimensions; Samsung's sheets are written per base model). The RF29BB8600 spec sheet gives the smaller 2.5 in hinge-side figure; the larger is stored. Sibling evidence: Will-it-fit sheet "MODEL RF29BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Same Samsung base model as RF29BB8600QLAA (identical stored dimensions; Samsung's sheets are written per base model). The RF29BB8600 spec sheet gives the smaller 2.5 in hinge-side figure; the larger is stored. Sibling evidence: Will-it-fit sheet "MODEL RF29BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall. Calculation or inference: agent blind extraction visually confirmed.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

Samsung measurement source — rf29bb860012aa.html
www.4brothersappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacture
Reviewed: 2026-09-09

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint.

Why this value was used

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.