Measurement evidence for Samsung RF27CG5B30SRAA

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — fdr-refrigerator-rf6500-family-hub-31-cu-ft-silver-rf27cg5b30sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Width (inch) 35.75 inch.
Reviewed: 2026-09-04

Official exact-model page: Net Width (inch) 35.75 inch.

Why this value was used

Official exact-model page: Net Width (inch) 35.75 inch.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — fdr-refrigerator-rf6500-family-hub-31-cu-ft-silver-rf27cg5b30sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Case Height without Hinge 68.875 in; height with hinge is separately
Reviewed: 2026-09-04

Official exact-model page: Net Case Height without Hinge 68.875 in; height with hinge is separately 70 in.

Why this value was used

Official exact-model page: Net Case Height without Hinge 68.875 in; height with hinge is separately 70 in.

Other evidence found

• 70 in — superseded

  The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: 8 x 1778 x 806 mm Net Width (inch) 35.75 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch Net D. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — fdr-refrigerator-rf6500-family-hub-31-cu-ft-silver-rf27cg5b30sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: 778 x 806 mm Net Width (inch) 35.75 inch Net Case Height with Hinge 70 inch Net Case Height without
Reviewed: 2026-09-04

778 x 806 mm Net Width (inch) 35.75 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch Net D

Why this value was used

778 x 806 mm Net Width (inch) 35.75 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch Net D

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — fdr-refrigerator-rf6500-family-hub-31-cu-ft-silver-rf27cg5b30sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Depth without Door 25 in; depth without door handle is separately 29.
Reviewed: 2026-09-04

Official exact-model page: Net Depth without Door 25 in; depth without door handle is separately 29.438 in.

Why this value was used

Official exact-model page: Net Depth without Door 25 in; depth without door handle is separately 29.438 in.

Other evidence found

• 29.438 in — superseded

  The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: 75 inch Net Depth with Door Handle 31.75 inch Net Depth without Door Handle 29.438 inch Net Depth without Door 25 inch Packing Dimensio. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.438 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — fdr-refrigerator-rf6500-family-hub-31-cu-ft-silver-rf27cg5b30sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Depth without Door Handle 29.438 in.
Reviewed: 2026-09-04

Official exact-model page: Net Depth without Door Handle 29.438 in.

Why this value was used

Official exact-model page: Net Depth without Door Handle 29.438 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf27cg5b30sraa
amdirectappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle = 31.75 in | s and Door | 35 3/4 x 68 7/8 x 25 inch | | Width (decimal) | 35.
Reviewed: 2026-09-04

Depth with Door Handle = 31.75 in | s and Door | 35 3/4 x 68 7/8 x 25 inch | | Width (decimal) | 35.75 inch | | Net Depth with Door Handle | 31.75 inch | | Product Dimensions without Door without Handles | 35.75 x 70 x 25 inch |

Why this value was used

Depth with Door Handle = 31.75 in | s and Door | 35 3/4 x 68 7/8 x 25 inch | | Width (decimal) | 35.75 inch | | Net Depth with Door Handle | 31.75 inch | | Product Dimensions without Door without Handles | 35.75 x 70 x 25 inch |

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-brand product-class chassis propagation from RF27CG5100SR

Confidence label: medium.

Primary evidence

Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Medium-confidence chassis inference from RF27CG5100SR. Donors unanimously report depth_doors_open_90
Reviewed: 2026-09-04

Medium-confidence chassis inference from RF27CG5100SR. Donors unanimously report depth_doors_open_90_in=44.0 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: 90-degree top-view product depth 44 in

Why this value was used

Medium-confidence chassis inference from RF27CG5100SR. Donors unanimously report depth_doors_open_90_in=44.0 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: 90-degree top-view product depth 44 in Calculation or inference: same-brand product-class chassis propagation from RF27CG5100SR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — fdr-refrigerator-rf6500-family-hub-31-cu-ft-silver-rf27cg5b30sraa + side gap from the maker's document
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.

Why this value was used

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — 08eb11481b4c6b6a9a91e1ef030453e3fab8ad9defd70872ab0c5334e065d6db.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Samsung installation envelope: 25 in appliance endpoint + 1 in clearance = 26 in.

Why this value was used

Samsung installation envelope: 25 in appliance endpoint + 1 in clearance = 26 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF27CG5B10SRAA

Confidence label: medium.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF27CG5B10SRAA: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF27CG5400SR; original evidence: Stored reviewed evidence explicitly applies the same clearance to sides and top. Allow a 3/8" minimum clearance at sides and top

Why this value was used

Samsung documented sibling/platform propagation from RF27CG5B10SRAA: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF27CG5400SR; original evidence: Stored reviewed evidence explicitly applies the same clearance to sides and top. Allow a 3/8" minimum clearance at sides and top Calculation or inference: shared Samsung model family; evidence donor RF27CG5B10SRAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF27CG5B10SRAA

Confidence label: medium.

Primary evidence

Samsung measurement source — 08eb11481b4c6b6a9a91e1ef030453e3fab8ad9defd70872ab0c5334e065d6db.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF27CG5B10SRAA: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF27CG5400SR; original evidence: 1" minimum clearance at rear

Why this value was used

Samsung documented sibling/platform propagation from RF27CG5B10SRAA: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF27CG5400SR; original evidence: 1" minimum clearance at rear Calculation or inference: shared Samsung model family; evidence donor RF27CG5B10SRAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221357.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221357.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-10-03

Clearance table for RF27CG** and RF32CG**: width B 35 3/4 in (908 mm). The stored 35 in was a retail net-width figure.

Why this value was used

Clearance table for RF27CG** and RF32CG**: width B 35 3/4 in (908 mm). The stored 35 in was a retail net-width figure.

Other evidence found

• 35 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: case_width_in = 35.0 in; source_id=64509. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.