Measurement evidence for Samsung RF27CG5400SR

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions with hinges, handles and doors: 35 3/4" x 70" x 31 3/4"

Why this value was used

Dimensions with hinges, handles and doors: 35 3/4" x 70" x 31 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Why this value was used

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 2023_RF27CG5400_CD_V4.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Product Dimensions height with hinges and doors. Family bridge: RF27CG5400SR is the finish/market-suffix variant of RF27CG5400SRAA; shared high-confidence endpoints match.

Why this value was used

Product Dimensions height with hinges and doors. Family bridge: RF27CG5400SR is the finish/market-suffix variant of RF27CG5400SRAA; shared high-confidence endpoints match.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 2023_RF27CG5400_CD_V4.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Product Dimensions depth without hinges and door. Family bridge: RF27CG5400SR is the finish/market-suffix variant of RF27CG5400SRAA; shared high-confidence endpoints match.

Why this value was used

Product Dimensions depth without hinges and door. Family bridge: RF27CG5400SR is the finish/market-suffix variant of RF27CG5400SRAA; shared high-confidence endpoints match.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions with hinge and door, no handle: 35 3/4" x 70" x 30 1/4"

Why this value was used

Dimensions with hinge and door, no handle: 35 3/4" x 70" x 30 1/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions with hinges, handles and doors: 35 3/4" x 70" x 31 3/4"

Why this value was used

Dimensions with hinges, handles and doors: 35 3/4" x 70" x 31 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Depth with door open 90°: 44"

Why this value was used

Depth with door open 90°: 44"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf + RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 70.0 in plus documented top clearance 0.375 in.

Why this value was used

Minimum opening height derived from highest appliance endpoint 70.0 in plus documented top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — 08eb11481b4c6b6a9a91e1ef030453e3fab8ad9defd70872ab0c5334e065d6db.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Allow a 3/8" minimum clearance at sides and top

Why this value was used

Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Allow a 3/8" minimum clearance at sides and top

Why this value was used

Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: top_clearance_in = reviewed side clearance because source explicitly states sides and top

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Stored reviewed evidence explicitly applies the same clearance to sides and top. Allow a 3/8" minimum clearance at sides and top

Why this value was used

Stored reviewed evidence explicitly applies the same clearance to sides and top. Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 08eb11481b4c6b6a9a91e1ef030453e3fab8ad9defd70872ab0c5334e065d6db.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1" minimum clearance at rear

Why this value was used

1" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 94883444.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The spec sheet's 2.5 in is the space where the handle may make contact (same reading as RS27T5200SR/AA, batch 7).

Why this value was used

When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The spec sheet's 2.5 in is the space where the handle may make contact (same reading as RS27T5200SR/AA, batch 7).

Other evidence found

• 2.5 in — superseded

  www.canadianappliance.ca; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). 2. Refer to illustration below to determine dimensions. | 3. Allow 2.5" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF27CG5400SRAA-spec-sheet-canada.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Why this value was used

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.