This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-03. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Product Dimensions height without hinges and door.
Product Dimensions height without hinges and door.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf assets.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf assets.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Product Dimensions closed depth without a projecting handle.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Product Dimensions closed maximum depth including the shown handle configuration.
Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=44.0 in from RF27C
Value used by ExactFit
44 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=44.0 in from RF27CG5100SR
Confidence label: medium.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=44.0 in from RF27C Reviewed: 2026-09-04
Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=44.0 in from RF27CG5100SR
Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=44.0 in from RF27CG5100SR Calculation or inference: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=44.0 in from RF27CG5100SR.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 35.75 + 2 * 0.375
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Closed product width plus the explicitly required clearance at each side.
Closed product width plus the explicitly required clearance at each side. Calculation or inference: 35.75 + 2 * 0.375.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 70 + 0.375
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Height with hinges plus the explicitly required top clearance.
Height with hinges plus the explicitly required top clearance. Calculation or inference: 70 + 0.375.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 25 + 1
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Case depth without door plus the explicitly required rear clearance.
Case depth without door plus the explicitly required rear clearance. Calculation or inference: 25 + 1.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Allow 0.375 in minimum clearance at sides and top.
Allow 0.375 in minimum clearance at sides and top.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Allow 0.375 in minimum clearance at sides and top.
Allow 0.375 in minimum clearance at sides and top.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Allow 0.375 in minimum clearance at sides and top.
Allow 0.375 in minimum clearance at sides and top.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 105583948.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-10-03
When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Other evidence found
2.5 in — superseded
image-stgus.samsung.com; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 2.5 in clearance on hinge side when installing next to a wall.. The final reviewed registry supersedes this earlier audit value.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Visually labeled cabinet/product width on the dimension drawing.
Selected: 3.75 in. Earlier retained values: 2.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Model numbers covered: RF27CG5100SRAA. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-03. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
