Measurement evidence for Samsung RF27CG5010S9

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 774804_en.pdf
media.datatail.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

WIDTH (FITS 36" OPENING): 35 3/4"

Why this value was used

WIDTH (FITS 36" OPENING): 35 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 774804_en.pdf
media.datatail.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Why this value was used

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 935f66ed-63f6-4e6f-96db-51627d321cd7.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: DEL RF27CG5010S9 DIMENSIONS DEPTH TO DOOR 291/2 " HEIGHT WITH HINGE 70" HEIGHT WITHOUT HINGE 687/8 "
Reviewed: 2026-09-04

DEL RF27CG5010S9 DIMENSIONS DEPTH TO DOOR 291/2 " HEIGHT WITH HINGE 70" HEIGHT WITHOUT HINGE 687/8 " DEPTH WITHOUT DOOR 2

Why this value was used

DEL RF27CG5010S9 DIMENSIONS DEPTH TO DOOR 291/2 " HEIGHT WITH HINGE 70" HEIGHT WITHOUT HINGE 687/8 " DEPTH WITHOUT DOOR 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 935f66ed-63f6-4e6f-96db-51627d321cd7.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: EIGHT WITH HINGE 70" HEIGHT WITHOUT HINGE 687/8 " DEPTH WITHOUT DOOR 25" WIDTH (FITS 36"
Reviewed: 2026-09-04

EIGHT WITH HINGE 70" HEIGHT WITHOUT HINGE 687/8 " DEPTH WITHOUT DOOR 25" WIDTH (FITS 36"

Why this value was used

EIGHT WITH HINGE 70" HEIGHT WITHOUT HINGE 687/8 " DEPTH WITHOUT DOOR 25" WIDTH (FITS 36"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 774804_en.pdf
media.datatail.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

DEPTH TO DOOR: 29 1/2"

Why this value was used

DEPTH TO DOOR: 29 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 774804_en.pdf
media.datatail.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions with hinges, handles and doors: 35 3/4" x 70" x 29 1/2"

Why this value was used

Dimensions with hinges, handles and doors: 35 3/4" x 70" x 29 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 327781437
www.homedepot.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth 3-Door Fingerprint ... Depth With Door Open 90 Degrees = 44.0 in | Samsung 27 cu. Ft. Counter
Reviewed: 2026-09-04

Depth 3-Door Fingerprint ... Depth With Door Open 90 Degrees = 44.0 in | Samsung 27 cu. Ft. Counter Depth 3-Door Fingerprint ... Depth With Door Open 90 Degrees (in.) 44 in. Height to Top of Door Hinge ... This guide provides installation information fo

Why this value was used

Depth 3-Door Fingerprint ... Depth With Door Open 90 Degrees = 44.0 in | Samsung 27 cu. Ft. Counter Depth 3-Door Fingerprint ... Depth With Door Open 90 Degrees (in.) 44 in. Height to Top of Door Hinge ... This guide provides installation information fo

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 774804_en.pdf
media.datatail.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

WIDTH (FITS 36" OPENING)

Why this value was used

WIDTH (FITS 36" OPENING)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.

Why this value was used

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — ec3fe58be900341205deca677b372e032c7f82453d8a60566b8c4092dc8e1606.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF27CG5100SR

Confidence label: medium.

Primary evidence

Samsung measurement source — 2023_RF27CG5100_CD_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung documented sibling/platform propagation from RF27CG5100SR: Exact-model cached Samsung cleara
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF27CG5100SR: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 3 copy/copies, 2 domain(s), official=True; no contrary parsed value.

Why this value was used

Samsung documented sibling/platform propagation from RF27CG5100SR: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 3 copy/copies, 2 domain(s), official=True; no contrary parsed value. Calculation or inference: shared Samsung model family; evidence donor RF27CG5100SR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ec3fe58be900341205deca677b372e032c7f82453d8a60566b8c4092dc8e1606.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

2" minimum clearance at rear

Why this value was used

2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 94883444.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The spec sheet's 2.5 in is the space where the handle may make contact (same reading as RS27T5200SR/AA, batch 7).

Why this value was used

When you install the refrigerator next to a fixed wall, you must provide a minimum clearance of 3 3/4 in (95 mm) from the wall to allow the door to swing open. The spec sheet's 2.5 in is the space where the handle may make contact (same reading as RS27T5200SR/AA, batch 7).

Other evidence found

• 2.5 in — superseded

  image-us.samsung.com; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). 2. Refer to illustration below to determine dimensions. | 3. Allow 2.5" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact. | deterministic pattern: hinge_side_wall. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 774804_en.pdf
media.datatail.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Why this value was used

Dimensions without hinges and door: 35 3/4" x 68 7/8" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.