Measurement evidence for Samsung RF25C5A01SRAA

Value used by ExactFit

32.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf25c5a01sraa-fdr-beverage-center-25-cu-ft-silver-rf25c5a01sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Net Width = 32.1875 in | ion (WxHxD) 32.3 x 70.0 x 35.625 inch Net Dimension (WxHxD) 820 x 1778 x 90
Reviewed: 2026-09-04

Net Width = 32.1875 in | ion (WxHxD) 32.3 x 70.0 x 35.625 inch Net Dimension (WxHxD) 820 x 1778 x 904 mm Net Width (inch) 32.1875 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch

Why this value was used

Net Width = 32.1875 in | ion (WxHxD) 32.3 x 70.0 x 35.625 inch Net Dimension (WxHxD) 820 x 1778 x 904 mm Net Width (inch) 32.1875 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf25c5a01sraa-fdr-beverage-center-25-cu-ft-silver-rf25c5a01sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Case Height without Hinge 68.875 in; 70 in is height with hinge.
Reviewed: 2026-09-04

Official exact-model page: Net Case Height without Hinge 68.875 in; 70 in is height with hinge.

Why this value was used

Official exact-model page: Net Case Height without Hinge 68.875 in; 70 in is height with hinge.

Other evidence found

• 70 in — superseded

  The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: x 1778 x 904 mm Net Width (inch) 32.1875 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch Net D. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf25c5a01sraa-fdr-beverage-center-25-cu-ft-silver-rf25c5a01sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: 8 x 904 mm Net Width (inch) 32.1875 inch Net Case Height with Hinge 70 inch Net Case Height without
Reviewed: 2026-09-04

8 x 904 mm Net Width (inch) 32.1875 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch Net D

Why this value was used

8 x 904 mm Net Width (inch) 32.1875 inch Net Case Height with Hinge 70 inch Net Case Height without Hinge 68.875 inch Net D

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf25c5a01sraa-fdr-beverage-center-25-cu-ft-silver-rf25c5a01sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Depth without Door 29.75 in; 33.313 in is depth without handle.
Reviewed: 2026-09-04

Official exact-model page: Net Depth without Door 29.75 in; 33.313 in is depth without handle.

Why this value was used

Official exact-model page: Net Depth without Door 29.75 in; 33.313 in is depth without handle.

Other evidence found

• 33.313 in — superseded

  The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: 5 inch Net Depth with Door Handle 35.625 inch Net Depth without Door Handle 33.313 inch Net Depth without Door 29.75 inch Packing Dimen. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.313 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf25c5a01sraa-fdr-beverage-center-25-cu-ft-silver-rf25c5a01sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Depth without Door Handle 33.313 in.
Reviewed: 2026-09-04

Official exact-model page: Net Depth without Door Handle 33.313 in.

Why this value was used

Official exact-model page: Net Depth without Door Handle 33.313 in.

Other evidence found

• 33 in — superseded

  The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: depth_less_handles_in = 33.0 in; source_id=65023. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf25c5a01sraa-samsung-bespoke-ai-3-door-french-doo
www.phelansplace.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle = 35.625 in | ht with Hinge | 70 inch | | Net Case Height without Hinge | 68.
Reviewed: 2026-09-04

Depth with Door Handle = 35.625 in | ht with Hinge | 70 inch | | Net Case Height without Hinge | 68.875 inch | | Net Depth with Door Handle | 35.625 inch | | Net Depth without Door Handle | 33.313 inch | | Net Depth without Door |

Why this value was used

Depth with Door Handle = 35.625 in | ht with Hinge | 70 inch | | Net Case Height without Hinge | 68.875 inch | | Net Depth with Door Handle | 35.625 inch | | Net Depth without Door Handle | 33.313 inch | | Net Depth without Door |

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

46.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf25c5a01sraa-fdr-beverage-center-25-cu-ft-silver-rf25c5a01sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model cached page: total depth with refrigerator door opened to 90 degrees is 46 3/4
Reviewed: 2026-09-04

Official exact-model cached page: total depth with refrigerator door opened to 90 degrees is 46 3/4 in.

Why this value was used

Official exact-model cached page: total depth with refrigerator door opened to 90 degrees is 46 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 32.1875 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — rf25c5a01sraa-samsung-bespoke-ai-3-door-french-doo + side gap from the maker's document
www.phelansplace.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 32.9375 in from product width 32.1875 in and explicit 0.375 in clearan
Reviewed: 2026-09-04

Derived minimum opening width 32.9375 in from product width 32.1875 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 32.9375 in from product width 32.1875 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 32.1875 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — samsung-rf27t5501s-product-guide.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.

Why this value was used

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — RF25C5551SR-specs.pdf
assets.coastappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 29.75 in appliance endpoint + 2 in clearance = 31.75 in.
Reviewed: 2026-09-05

Samsung installation envelope: 29.75 in appliance endpoint + 2 in clearance = 31.75 in.

Why this value was used

Samsung installation envelope: 29.75 in appliance endpoint + 2 in clearance = 31.75 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — samsung-rf27t5501s-product-guide.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — samsung-rf27t5501s-product-guide.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — samsung-rf27t5501s-product-guide.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top
Reviewed: 2026-09-05

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Why this value was used

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF25C5551SRAA

Confidence label: medium.

Primary evidence

Samsung measurement source — RF25C5551SR-specs.pdf
assets.coastappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung documented sibling/platform propagation from RF25C5551SRAA: Cached exact-model result: Allow
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF25C5551SRAA: Cached exact-model result: Allow 2" minimum clearance at rear

Why this value was used

Samsung documented sibling/platform propagation from RF25C5551SRAA: Cached exact-model result: Allow 2" minimum clearance at rear Calculation or inference: shared Samsung model family; evidence donor RF25C5551SRAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Samsung measurement source — 106221386.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). minimum clearance of 3 3/4" (95 mm) from the wall

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). minimum clearance of 3 3/4" (95 mm) from the wall

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

5.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105583933.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 21
Reviewed: 2026-10-14

5 1/4 in printed for doors fully open to the printed 135 degrees. Read by the verification agent (run D91ab4ff9fb) from a document naming the model.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

5 1/4 in printed for doors fully open to the printed 135 degrees. Read by the verification agent (run D91ab4ff9fb) from a document naming the model.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung Net Width mapped to cabinet/case width

Confidence label: medium.

Primary evidence

Samsung measurement source — rf25c5a01sraa-fdr-beverage-center-25-cu-ft-silver-rf25c5a01sraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Samsung cached specification: case_width_in = 32.0 in; source_id=65023
Reviewed: 2026-09-04

Official Samsung cached specification: case_width_in = 32.0 in; source_id=65023

Why this value was used

Official Samsung cached specification: case_width_in = 32.0 in; source_id=65023 Calculation or inference: Samsung Net Width mapped to cabinet/case width.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.