Measurement evidence for Samsung RF23DB9900QDAA

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf23db9900qdaa
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed exact-model cached label: Width = 35.875 in. Context: Height without Hinge 70.75" Net Dept
Reviewed: 2026-09-04

Reviewed exact-model cached label: Width = 35.875 in. Context: Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Width 35 7/8" Height 73" Height (decimal) 73 Depth (decimal) 28.75 Width (decimal) 35.88 Height (extra) + 2 inches for vent

Why this value was used

Reviewed exact-model cached label: Width = 35.875 in. Context: Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Width 35 7/8" Height 73" Height (decimal) 73 Depth (decimal) 28.75 Width (decimal) 35.88 Height (extra) + 2 inches for vent

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105583978.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

Clearance table for RF23DB******: A depth 28 3/4 in (731 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). Case height is C.

Why this value was used

Clearance table for RF23DB******: A depth 28 3/4 in (731 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). Case height is C.

Other evidence found

• 73 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: t ### * Energy Consumption 631 kWh/year ### * Net Case Height with Hinge 73 inch * Net Case Height without Hinge 70.75 inch * Ne. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 70 in — superseded

  groveappliance.com; location not retained. Model scope: not separately recorded. Raw value: Exact-model cached Samsung specification: height_case_in = 70.0 in; source_id=65910. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105583978.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

Clearance table for RF23DB******: A depth 28 3/4 in (731 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). The stored field holds the appliance's highest point, the overall height D (owner rule).

Why this value was used

Clearance table for RF23DB******: A depth 28 3/4 in (731 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). The stored field holds the appliance's highest point, the overall height D (owner rule).

Other evidence found

• 70 in — superseded

  image-us.samsung.com; location not retained. Model scope: not separately recorded. Raw value: DOOR 283/ 4 " WIDTH (FITS 36" OPENING) 35 3/ 4 " HEIGHT WITH HINGE 70" Be sure your new fridge will fit Don't wait until. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RF23BB8900_V2.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: 23 cu. ft. 4-Door French Door Refrigerator A B D DEPTH WITHOUT DOOR 24 " DEPTH TO DOOR 283/ 4 " WIDT
Reviewed: 2026-09-04

23 cu. ft. 4-Door French Door Refrigerator A B D DEPTH WITHOUT DOOR 24 " DEPTH TO DOOR 283/ 4 " WIDTH (FITS 36" OPENING) 3

Why this value was used

23 cu. ft. 4-Door French Door Refrigerator A B D DEPTH WITHOUT DOOR 24 " DEPTH TO DOOR 283/ 4 " WIDTH (FITS 36" OPENING) 3

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105583978.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

Clearance table for RF23DB******: A depth 28 3/4 in (731 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). The stored 28 in was a retail figure.

Why this value was used

Clearance table for RF23DB******: A depth 28 3/4 in (731 mm), C height without hinge 70 3/4 in (1797 mm), D overall height 73 in (1853 mm), E height with hinge 72 in (1830 mm). The stored 28 in was a retail figure.

Other evidence found

• 28 in — superseded

  groveappliance.com; location not retained. Model scope: not separately recorded. Raw value: Exact-model cached Samsung specification: depth_less_handles_in = 28.0 in; source_id=65910. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf23db9900qdaa
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Depth with Door Handle = 28.75 in | 5" (H) x 24" (D) Shipping Dime
Reviewed: 2026-09-04

Exact-model cached specification: Depth with Door Handle = 28.75 in | 5" (H) x 24" (D) Shipping Dimensions 38.25" (W) x 78.625" (H) x 30 5/8" (D) Net Depth with Door Handle 28.75" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Ha

Why this value was used

Exact-model cached specification: Depth with Door Handle = 28.75 in | 5" (H) x 24" (D) Shipping Dimensions 38.25" (W) x 78.625" (H) x 30 5/8" (D) Net Depth with Door Handle 28.75" Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Ha

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same RF23DB chassis as RF23DB960012AA/RF23DB970012AA/RF23DB9700QLAA

Confidence label: medium.

Primary evidence

Samsung measurement source — documents for other models on the same chassis
static.pcrichard.com · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Retained specification excerpt: RF23DB sibling models unanimously report 43 in open-door depth.
Reviewed: 2026-09-04

RF23DB sibling models unanimously report 43 in open-door depth.

Why this value was used

RF23DB sibling models unanimously report 43 in open-door depth. Calculation or inference: same RF23DB chassis as RF23DB960012AA/RF23DB970012AA/RF23DB9700QLAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.875 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — rf23db9900qdaa + side gap from the maker's document
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.625 in from product width 35.875 in and explicit 0.375 in clearance
Reviewed: 2026-09-04

Derived minimum opening width 36.625 in from product width 35.875 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.625 in from product width 35.875 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.875 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-03

Recalculated 2026-10-04 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 70.75, height_hinge_in = 73, top_clearance_in = 0.375 = 73.375 in (previously 70.375 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 70.75, height_hinge_in = 73, top_clearance_in = 0.375 = 73.375 in (previously 70.375 in). Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

• 70.375 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — WillitFit_RF23BB8900_V2.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 24 in appliance endpoint + 2 in clearance = 26 in.
Reviewed: 2026-09-05

Samsung installation envelope: 24 in appliance endpoint + 2 in clearance = 26 in.

Why this value was used

Samsung installation envelope: 24 in appliance endpoint + 2 in clearance = 26 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-29

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-29

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF23DB990012AA

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF23DB990012AA: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RM80F23VMR; original evidence: Stored reviewed evidence explicitly applies the same clearance to sides and top. Exact-model Samsung fit guide: allow a 3/8" minimum clearance at sides and top.

Why this value was used

Samsung documented sibling/platform propagation from RF23DB990012AA: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RM80F23VMR; original evidence: Stored reviewed evidence explicitly applies the same clearance to sides and top. Exact-model Samsung fit guide: allow a 3/8" minimum clearance at sides and top. Calculation or inference: shared Samsung model family; evidence donor RF23DB990012AA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF23BB8900_V2.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow 2" minimum clearance at rear
Reviewed: 2026-09-05

Cached exact-model result: Allow 2" minimum clearance at rear

Why this value was used

Cached exact-model result: Allow 2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF23DB9700_2026-10-30.pdf
Samsung · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF23DB9700, the same fridge as RF23DB9900 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Why this value was used

Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF23DB9700, the same fridge as RF23DB9900 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

11.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9900QD_2026-10-30.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-30

Samsung RF23DB9900 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Why this value was used

Samsung RF23DB9900 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

Samsung measurement source — rf23db9900qdaa
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same-appliance endpoint inference: case width equals exact stored closed width 35.875 in; manufactur
Reviewed: 2026-09-09

Same-appliance endpoint inference: case width equals exact stored closed width 35.875 in; manufacturer does not label a separate case-width endpoint.

Why this value was used

Same-appliance endpoint inference: case width equals exact stored closed width 35.875 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.