Measurement evidence for Samsung RF23DB9700QLAA

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions with hinges, handles and doors: width 35 7/8 in
Reviewed: 2026-09-04

Dimensions with hinges, handles and doors: width 35 7/8 in

Why this value was used

Dimensions with hinges, handles and doors: width 35 7/8 in

Other evidence found

• 35.88 in — superseded

  appliancehomestore.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Width = 35.88 in | ) | 24" | | Height | 73" | | Height (decimal) | 73 | | Width (decimal) | 35.875 | [...] | | | --- | | Width | 35.88 in. | | Height | 73 in. | | Length | 28 in. | | Weight | 337.3 lbs. | | Shipping Weight (lbs.) | 357.1 | | Shipping Weight . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-counter-depth-4-door-flex-refrigerator-23-cu-ft-with-beverage-zone-and-auto-open-door-in-stainless-steel-sku-rf23db9700qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height without Hinge = 70.75 in | H) x 30 5/8" (D) Net Depth with Door Handle 28.75 Net Height with
Reviewed: 2026-09-04

Height without Hinge = 70.75 in | H) x 30 5/8" (D) Net Depth with Door Handle 28.75 Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Height 73" Height

Why this value was used

Height without Hinge = 70.75 in | H) x 30 5/8" (D) Net Depth with Door Handle 28.75 Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Height 73" Height

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Why this value was used

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-counter-depth-4-door-flex-refrigerator-23-cu-ft-with-beverage-zone-and-auto-open-door-in-stainless-steel-sku-rf23db9700qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door = 24.0 in | with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Han
Reviewed: 2026-09-04

Depth without Door = 24.0 in | with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Height 73" Height (decimal) 73 Width (decimal) 35.875 Depth (decimal) 28.75 Wid

Why this value was used

Depth without Door = 24.0 in | with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Height 73" Height (decimal) 73 Width (decimal) 35.875 Depth (decimal) 28.75 Wid

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-counter-depth-4-door-flex-refrigerator-23-cu-ft-with-beverage-zone-and-auto-open-door-in-stainless-steel-sku-rf23db9700qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth w/o Door Handle: 28.75 in | Door Handle 28.75 Net Height with Hinge 73" Net Height without Hin
Reviewed: 2026-09-04

Depth w/o Door Handle: 28.75 in | Door Handle 28.75 Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Height 73" Height (decimal) 73 Width (decimal) 35.8

Why this value was used

Depth w/o Door Handle: 28.75 in | Door Handle 28.75 Net Height with Hinge 73" Net Height without Hinge 70.75" Net Depth w/o Door Handle 28.75" Depth without Door (in) 24" Height 73" Height (decimal) 73 Width (decimal) 35.8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions with hinges, handles and doors: depth 28 3/4 in
Reviewed: 2026-09-04

Dimensions with hinges, handles and doors: depth 28 3/4 in

Why this value was used

Dimensions with hinges, handles and doors: depth 28 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 90-degree top-view product depth 43 in
Reviewed: 2026-09-04

90-degree top-view product depth 43 in

Why this value was used

90-degree top-view product depth 43 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.625

Confidence label: high.

Calculation inputs: Overall width; Left-side ventilation clearance;

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearan
Reviewed: 2026-09-18

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.625 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged.

Why this value was used

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.625 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged. Calculation or inference: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.625.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 73 + 0.375

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
device.report · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Height with hinges plus the explicitly required 3/8 in top clearance.

Why this value was used

Height with hinges plus the explicitly required 3/8 in top clearance. Calculation or inference: 73 + 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24 + 2

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Case depth without doors plus the explicitly required 2 in rear clearance.

Why this value was used

Case depth without doors plus the explicitly required 2 in rear clearance. Calculation or inference: 24 + 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow a 3/8 in minimum clearance at sides and top.

Why this value was used

Allow a 3/8 in minimum clearance at sides and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow a 3/8 in minimum clearance at sides and top.

Why this value was used

Allow a 3/8 in minimum clearance at sides and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow a 3/8 in minimum clearance at sides and top.

Why this value was used

Allow a 3/8 in minimum clearance at sides and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow 2 in minimum clearance at rear.

Why this value was used

Allow 2 in minimum clearance at rear.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF23DB9700_2026-10-30.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for this model. The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Why this value was used

Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for this model. The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Other evidence found

• 2.5 in — superseded

  image-stgus.samsung.com; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Allow 2.5 in of clearance on hinge side of refrigerator when installing next to a wall.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

11.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700QL_2026-10-30.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-30

Samsung RF23DB9700 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Why this value was used

Samsung RF23DB9700 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions without hinges and door: width 35 7/8 in
Reviewed: 2026-09-04

Dimensions without hinges and door: width 35 7/8 in

Why this value was used

Dimensions without hinges and door: width 35 7/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.