Measurement evidence for Samsung RF23DB970012AA

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Why this value was used

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Other evidence found

• 35.88 in — superseded

  groveappliance.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Width = 35.88 in | Samsung RF23DB970012AA French Door Refrigerators | Ohio | Grove | | | --- | | Width | 35.88 in. | | Height | 73 in. | | Length | 28 in. | | Weight | 343.9 lbs. | | Shipping Weight (lbs.) | 363.8 | | Shipping Weight . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in.

Why this value was used

Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Why this value was used

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in.

Why this value was used

Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Why this value was used

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in; Auto Open Door model has no projecting bar handle.

Why this value was used

Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in; Auto Open Door model has no projecting bar handle.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-brand product-class chassis propagation from RF23DB9700QLAA

Confidence label: medium.

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Medium-confidence chassis inference from RF23DB9700QLAA. Donors unanimously report depth_doors_open_
Reviewed: 2026-09-04

Medium-confidence chassis inference from RF23DB9700QLAA. Donors unanimously report depth_doors_open_90_in=43.0 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: 90-degree top-view product depth 43 in

Why this value was used

Medium-confidence chassis inference from RF23DB9700QLAA. Donors unanimously report depth_doors_open_90_in=43.0 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: 90-degree top-view product depth 43 in Calculation or inference: same-brand product-class chassis propagation from RF23DB9700QLAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.875 + 2 * 0.375

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product width plus the explicitly required 3/8 in clearance at each side.

Why this value was used

Product width plus the explicitly required 3/8 in clearance at each side. Calculation or inference: 35.875 + 2 * 0.375.

Other evidence found

• 36.63 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 36.63 in from product width 35.88 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 73 + 0.375

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Height with hinges plus the explicitly required 3/8 in top clearance.

Why this value was used

Height with hinges plus the explicitly required 3/8 in top clearance. Calculation or inference: 73 + 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24 + 2

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Case depth without doors plus the explicitly required 2 in rear clearance.

Why this value was used

Case depth without doors plus the explicitly required 2 in rear clearance. Calculation or inference: 24 + 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8 in minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8 in minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8 in minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8 in minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow a 3/8 in minimum clearance at sides and top.

Why this value was used

Allow a 3/8 in minimum clearance at sides and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow 2 in minimum clearance at rear.

Why this value was used

Allow 2 in minimum clearance at rear.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — WillitFit_RF23DB9700_2026-10-30.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for this model. The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Why this value was used

Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for this model. The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.

Other evidence found

• 2.5 in — superseded

  image-stgus.samsung.com; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Allow 2.5 in of clearance on hinge side of refrigerator when installing next to a wall.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

11.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700QL_2026-10-30.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-30

Samsung RF23DB9700 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Why this value was used

Samsung RF23DB9700 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF23DB9700_Counter_Depth_V3.pdf
groveappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in.

Why this value was used

Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in.

Other evidence found

• 35.88 in — superseded

  groveappliance.com; location not retained. Model scope: not separately recorded. Raw value: Low-confidence same-appliance width mapping: case_width_in=35.88 in from width_doors_closed_in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 35.88 in — superseded

  groveappliance.com; location not retained. Model scope: not separately recorded. Raw value: Same-appliance endpoint inference: case width equals exact stored closed width 35.88 in; manufacturer does not label a separate case-width endpoint.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.