This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-30. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-09-09
RF23DB****** Height without hinge C: 70 3/4 in (1797 mm)
RF23DB****** Height without hinge C: 70 3/4 in (1797 mm)
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-09
Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in
Dimensions without hinges and doors: 35 7/8 x 70 3/4 x 24 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-09-09
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-09
Dimensions with hinges and doors: 35 7/8 x 73 x 28 3/4 in
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 23 Reviewed: 2026-09-09
RF23D******* dimension 07: 43 in (1093 mm), depth with door open 90 degrees
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — will-it-fit-guide-retailer-mirror.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-09-09
{"calculation": "73.0 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/truth-set/samsung-rf23db9600qlaa.json", "page": 22, "raw": "RF23DB****** Overall Height D: 73 in (1853 mm)", "source_url": "https://downloadcenter.samsung.com/content/UM/202604/20260430091836777/DA68-04752V-01_T-TYPE_RF9000D_EN_260424.pdf", "value_in": 73.0}], "top_clearance_in": [{"cache_path": "data/truth-set/samsung-rf23db9600qlaa.json", "page": 2, "raw": "Allow a 3/8 in minimum clearance at sides and top for ease of installation", "source_url": "https://image-us.samsung.com/SamsungUS/home/home-appliances/refrigerators/bespoke/rf23db960012aa/RF23DB9600_Counter_Depth_V3.pdf", "value_in": 0.375}]}, "result_in": 73.375}
{"calculation": "73.0 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/truth-set/samsung-rf23db9600qlaa.json", "page": 22, "raw": "RF23DB****** Overall Height D: 73 in (1853 mm)", "source_url": "https://downloadcenter.samsung.com/content/UM/202604/20260430091836777/DA68-04752V-01_T-TYPE_RF9000D_EN_260424.pdf", "value_in": 73.0}], "top_clearance_in": [{"cache_path": "data/truth-set/samsung-rf23db9600qlaa.json", "page": 2, "raw": "Allow a 3/8 in minimum clearance at sides and top for ease of installation", "source_url": "https://image-us.samsung.com/SamsungUS/home/home-appliances/refrigerators/bespoke/rf23db960012aa/RF23DB9600_Counter_Depth_V3.pdf", "value_in": 0.375}]}, "result_in": 73.375} Calculation or inference: 73.0 + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — will-it-fit-guide-retailer-mirror.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-09
Allow a 3/8 in minimum clearance at sides and top for ease of installation
Allow a 3/8 in minimum clearance at sides and top for ease of installation
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-09
Allow a 3/8 in minimum clearance at sides and top for ease of installation
Allow a 3/8 in minimum clearance at sides and top for ease of installation
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-09
Allow a 3/8 in minimum clearance at sides and top for ease of installation
Allow a 3/8 in minimum clearance at sides and top for ease of installation
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-09
Allow 2 in minimum clearance at rear for proper air circulation and water/electrical connections
Allow 2 in minimum clearance at rear for proper air circulation and water/electrical connections
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — WillitFit_RF23DB9700_2026-10-30.pdf Samsung · Web source Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-30
Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF23DB9700, the same fridge as RF23DB9600 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.
Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF23DB9700, the same fridge as RF23DB9600 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.
Why evidence from RF23DB9700QLAA applies
Target model: RF23DB9600QLAA. Supporting model: RF23DB9700QLAA. Manufacturer: Samsung. Product family and measurement relationship: Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF23DB9700, the same fridge as RF23DB9600 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall..
Measurement transferred: Wall clearance for door open to 90°. Relevant equivalence evidence: Samsung Will-it-fit sheet "MODEL RF23DB9700 DIMENSIONS": "Allow 3.75" of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." Sheet for RF23DB9700, the same fridge as RF23DB9600 (Samsung spec sheets for both print the identical dimension drawing). The largest door-swing clearance printed is stored (owner rule for clearances); the spec sheets' 2.5" is where the handle may touch the wall.. Known differences: not separately recorded. Reviewed 2026-10-30.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23DB9600QL_2026-10-30.pdf static.pcrichard.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-30
Samsung RF23DB9600 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).
Samsung RF23DB9600 spec sheet, Dimensions top view: each door fully open at 125 degrees reaches 11 3/4" past the cabinet side (59" across both open doors). Stored as the printed door projection past the cabinet side (owner decision 2026-10-17).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — samsung-rf23db9600qlaa.json Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-09-09
Model numbers covered: RF23DB9600QLAA. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-30. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
