This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-29. 6 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Retained specification excerpt: Plain exact-model specification row: Width = 35.75 in | without Hinge | 68 7/8" | | Net Depth w/o Do
Value used by ExactFit
35.75 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb89008maa www.drimmersusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Plain exact-model specification row: Width = 35.75 in | without Hinge | 68 7/8" | | Net Depth w/o Do Reviewed: 2026-09-04
Plain exact-model specification row: Width = 35.75 in | without Hinge | 68 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Height | 70" | | Net Depth with Door Handle | 28.75" | | Height (decimal) | 70 | | Width (decimal) | 35.75 | | Dept
Plain exact-model specification row: Width = 35.75 in | without Hinge | 68 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Height | 70" | | Net Depth with Door Handle | 28.75" | | Height (decimal) | 70 | | Width (decimal) | 35.75 | | Dept
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height without Hinge = 68.875 in | imensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge
Value used by ExactFit
68.875 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb89008maa www.drimmersusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Height without Hinge = 68.875 in | imensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge Reviewed: 2026-09-04
Height without Hinge = 68.875 in | imensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | W
Height without Hinge = 68.875 in | imensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | W
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Dimensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge | 70" | | Net Height without Hing
Value used by ExactFit
70 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb89008maa www.drimmersusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Dimensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge | 70" | | Net Height without Hing Reviewed: 2026-09-04
Dimensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Net De
Dimensions | 38 1/4" x 75 3/4" x 30 5/8" | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Net De
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" |
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb89008maa www.drimmersusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" | Reviewed: 2026-09-04
7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Height | 70" | | Net Dept
7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Height | 70" | | Net Dept
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth w/o Door Handle = 28.75 in | | | Net Height with Hinge | 70" | | Net Height without Hinge | 6
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb89008maa www.drimmersusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Depth w/o Door Handle = 28.75 in | | | Net Height with Hinge | 70" | | Net Height without Hinge | 6 Reviewed: 2026-09-04
Depth w/o Door Handle = 28.75 in | | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Height | 70" | | Net
Depth w/o Door Handle = 28.75 in | | | Net Height with Hinge | 70" | | Net Height without Hinge | 68 7/8" | | Net Depth w/o Door Handle | 28 3/4" | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Height | 70" | | Net
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Retained specification excerpt: Depth with Door Handle = 28.75 in | | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Heigh
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb89008maa www.drimmersusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Depth with Door Handle = 28.75 in | | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Heigh Reviewed: 2026-09-04
Depth with Door Handle = 28.75 in | | | Depth without Door (in) | 24" | | Width | 35 3/4" | | Height | 70" | | Net Depth with Door Handle | 28.75" | | Height (decimal) | 70 | | Width (decimal) | 35.75 | | Depth (decimal) | 28.
43 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: same-brand product-class chassis propagation from RF24BB6200QLAA, RF24BB6600QLAA, RF70F23DER
Confidence label: medium.
Primary evidence
Samsung measurement source — samsung-rf24bb6200qlaa www.homery.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Medium-confidence chassis inference from RF24BB6200QLAA, RF24BB6600QLAA, RF70F23DER. Donors unanimou Reviewed: 2026-09-04
Medium-confidence chassis inference from RF24BB6200QLAA, RF24BB6600QLAA, RF70F23DER. Donors unanimously report depth_doors_open_90_in=43.0 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in. Donor evidence: Depth With Door Opened At 90 Degrees = 43.0 in | Width:36" Width:35 3/4" Depth:28 3/4" Height:70" Depth Without Handles:28 3/4" Depth With Door Opened At 90 Degrees:43" Counter/Depth:Yes Height Without Hinges:68 7/8" Depth Without Door:24" ### Tech
Medium-confidence chassis inference from RF24BB6200QLAA, RF24BB6600QLAA, RF70F23DER. Donors unanimously report depth_doors_open_90_in=43.0 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in. Donor evidence: Depth With Door Opened At 90 Degrees = 43.0 in | Width:36" Width:35 3/4" Depth:28 3/4" Height:70" Depth Without Handles:28 3/4" Depth With Door Opened At 90 Degrees:43" Counter/Depth:Yes Height Without Hinges:68 7/8" Depth Without Door:24" ### Tech Calculation or inference: same-brand product-class chassis propagation from RF24BB6200QLAA, RF24BB6600QLAA, RF70F23DER.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Samsung measurement source — rf23bb89008maa + side gap from the maker's document www.drimmersusa.com
Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Value used by ExactFit
36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb89008maa + side gap from the maker's document www.drimmersusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on Reviewed: 2026-09-04
Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.
Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance Reviewed: 2026-09-05
Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance 0.375 in.
Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa Samsung · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Reviewed: 2026-09-05
Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.
Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an Reviewed: 2026-10-29
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an Reviewed: 2026-10-29
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evide
Value used by ExactFit
0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF70F23DER
Confidence label: medium.
Primary evidence
Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evide Reviewed: 2026-09-05
Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 4 copy/copies, 2 domain(s), official=True; no contrary parsed value.
Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 4 copy/copies, 2 domain(s), official=True; no contrary parsed value. Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF70F23DER.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original e
Value used by ExactFit
2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF24BB6200QLAA
Confidence label: medium.
Primary evidence
Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original e Reviewed: 2026-09-05
Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original evidence: 2 inches of space in the back
Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original evidence: 2 inches of space in the back Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF24BB6200QLAA.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 7322f9985ce6489e74eef5f107f58ec30650e6a48ef31a3a98571524439a60fe.pdf www.nfm.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-15
Will-it-fit sheet "MODEL RF23BB8900 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Will-it-fit sheet "MODEL RF23BB8900 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Other evidence found
2.5 in — superseded
www.nfm.com; location not retained. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Allow 2.5" of clearance on hinge side. The final reviewed registry supersedes this earlier audit value.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Selected: 3.75 in. Earlier retained values: 2.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Will-it-fit sheet "MODEL RF23BB8900 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Source documents and pages
Samsung measurement source — rf23bb89008maa
www.drimmersusa.com · Web source · secondary model/source
Model numbers covered: RF23BB89008MAA. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
7 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
