This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-29. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Retained specification excerpt: Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm
Value used by ExactFit
35.75 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — rf8000bc-4-door-french-door-beverage-center-23-cu-ft-silver-rf23bb8600qlaa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm Reviewed: 2026-09-04
Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm - Net Width (inch) 35.75 inch - Net Case Height with Hinge 70 inch - Net Case Height without Hinge 68.875 i
Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm - Net Width (inch) 35.75 inch - Net Case Height with Hinge 70 inch - Net Case Height without Hinge 68.875 i
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Product Dimensions height without hinges and door.
Product Dimensions height without hinges and door.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth without Door = 24.0 in | th with Door Handle 28.75 inch - Net Depth without Door Handle 28.75
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — rf8000bc-4-door-french-door-beverage-center-23-cu-ft-silver-rf23bb8600qlaa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth without Door = 24.0 in | th with Door Handle 28.75 inch - Net Depth without Door Handle 28.75 Reviewed: 2026-09-04
Depth without Door = 24.0 in | th with Door Handle 28.75 inch - Net Depth without Door Handle 28.75 inch - Net Depth without Door 24 inch - Packing Dimension (WxHxD) 37 5/7" x 75 2/5" x 30 5/9" - Net Weight 317.47 l
Depth without Door = 24.0 in | th with Door Handle 28.75 inch - Net Depth without Door Handle 28.75 inch - Net Depth without Door 24 inch - Packing Dimension (WxHxD) 37 5/7" x 75 2/5" x 30 5/9" - Net Weight 317.47 l
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Product Dimensions closed depth without a projecting handle.
Retained specification excerpt: Depth with Door Handle: 28.75 in | ase Height with Hinge 70 inch - Net Case Height without Hinge 68.
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — rf8000bc-4-door-french-door-beverage-center-23-cu-ft-silver-rf23bb8600qlaa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth with Door Handle: 28.75 in | ase Height with Hinge 70 inch - Net Case Height without Hinge 68. Reviewed: 2026-09-04
Depth with Door Handle: 28.75 in | ase Height with Hinge 70 inch - Net Case Height without Hinge 68.875 inch - Net Depth with Door Handle 28.75 inch - Net Depth without Door Handle 28.75 inch - Net Depth without Door 24 inch -
Depth with Door Handle: 28.75 in | ase Height with Hinge 70 inch - Net Case Height without Hinge 68.875 inch - Net Depth with Door Handle 28.75 inch - Net Depth without Door Handle 28.75 inch - Net Depth without Door 24 inch -
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Visually labeled 90-degree front-to-back envelope in the dimension drawing.
36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 35.75 + 2 * 0.375
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Closed product width plus the explicitly required clearance at each side.
Closed product width plus the explicitly required clearance at each side. Calculation or inference: 35.75 + 2 * 0.375.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 70 + 0.375
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Height with hinges plus the explicitly required top clearance.
Height with hinges plus the explicitly required top clearance. Calculation or inference: 70 + 0.375.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 24 + 1
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Case depth without door plus the explicitly required rear clearance.
Case depth without door plus the explicitly required rear clearance. Calculation or inference: 24 + 1.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-29
The document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top."
The document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-29
The document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top."
The document this model's measurements come from states: "Allow 0.375 in minimum clearance at sides and top."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Allow 0.375 in minimum clearance at sides and top.
Allow 0.375 in minimum clearance at sides and top.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 934032dda61e446bac8f0631e530355b062030012460ab15f0777b4acbc6df9c.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-15
Will-it-fit sheet "MODEL RF23BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Will-it-fit sheet "MODEL RF23BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Other evidence found
2.5 in — superseded
image-stgus.samsung.com; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 2.5 in clearance on hinge side when installing next to a wall.. The final reviewed registry supersedes this earlier audit value.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-10
Visually labeled cabinet/product width on the dimension drawing.
Visually labeled cabinet/product width on the dimension drawing.
Other evidence found
35 in — superseded
www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: case_width_in = 35.0 in; source_id=27716. The final reviewed registry supersedes this earlier audit value.
Selected: 3.75 in. Earlier retained values: 2.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Will-it-fit sheet "MODEL RF23BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Model numbers covered: RF23BB8600QLAA. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
12 displayed measurements supported: Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
