This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-29. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf appliancehomestore.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-11
Product Dimensions width with hinges and doors. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Product Dimensions width with hinges and doors. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height without Hinge: 68.88 in | with Handles 35 3/4" (W) x 70" (H) x 28 3/4" (D) Net Height with H
Value used by ExactFit
68.88 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — bespoke-4-door-french-door-refrigerator-23-cu-ft-with-beverage-center-in-morning-blue-glass-top-panels-and-white-glass-middle-and-bottom-panels-sku-rf23bb86004maa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Height without Hinge: 68.88 in | with Handles 35 3/4" (W) x 70" (H) x 28 3/4" (D) Net Height with H Reviewed: 2026-09-04
Height without Hinge: 68.88 in | with Handles 35 3/4" (W) x 70" (H) x 28 3/4" (D) Net Height with Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 28 3/4" Depth without Door (in) 24" Width 35 3/4" Hei
Height without Hinge: 68.88 in | with Handles 35 3/4" (W) x 70" (H) x 28 3/4" (D) Net Height with Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 28 3/4" Depth without Door (in) 24" Width 35 3/4" Hei
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-11
Product Dimensions height with hinges and doors. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Product Dimensions height with hinges and doors. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth without Door = 24.0 in | th Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Hand
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — bespoke-4-door-french-door-refrigerator-23-cu-ft-with-beverage-center-in-morning-blue-glass-top-panels-and-white-glass-middle-and-bottom-panels-sku-rf23bb86004maa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth without Door = 24.0 in | th Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Hand Reviewed: 2026-09-04
Depth without Door = 24.0 in | th Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 28 3/4" Depth without Door (in) 24" Width 35 3/4" Height 70" Height (extra) \+ 2 inches for ventillation Width (ext
Depth without Door = 24.0 in | th Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 28 3/4" Depth without Door (in) 24" Width 35 3/4" Height 70" Height (extra) \+ 2 inches for ventillation Width (ext
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth w/o Door Handle: 28.75 in | H) x 28 3/4" (D) Net Height with Hinge 70" Net Height without Hing
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — bespoke-4-door-french-door-refrigerator-23-cu-ft-with-beverage-center-in-morning-blue-glass-top-panels-and-white-glass-middle-and-bottom-panels-sku-rf23bb86004maa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth w/o Door Handle: 28.75 in | H) x 28 3/4" (D) Net Height with Hinge 70" Net Height without Hing Reviewed: 2026-09-04
Depth w/o Door Handle: 28.75 in | H) x 28 3/4" (D) Net Height with Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 28 3/4" Depth without Door (in) 24" Width 35 3/4" Height 70" Height (extra) \+ 2 inches
Depth w/o Door Handle: 28.75 in | H) x 28 3/4" (D) Net Height with Hinge 70" Net Height without Hinge 68 7/8" Net Depth w/o Door Handle 28 3/4" Depth without Door (in) 24" Width 35 3/4" Height 70" Height (extra) \+ 2 inches
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Retained specification excerpt: Depth with Door Handle: 28.75 in | sions without Hinges and Door 35 6/8" x 68 7/8" x 24" Width (deci
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — bespoke-4-door-french-door-refrigerator-23-cu-ft-with-beverage-center-in-morning-blue-glass-top-panels-and-white-glass-middle-and-bottom-panels-sku-rf23bb86004maa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth with Door Handle: 28.75 in | sions without Hinges and Door 35 6/8" x 68 7/8" x 24" Width (deci Reviewed: 2026-09-04
Depth with Door Handle: 28.75 in | sions without Hinges and Door 35 6/8" x 68 7/8" x 24" Width (decimal) 35.75 Net Depth with Door Handle 28 6/8" Product Dimensions with Door without Handles 35 3/4" (W) x 70" (H) x 28 3/4" (D
Depth with Door Handle: 28.75 in | sions without Hinges and Door 35 6/8" x 68 7/8" x 24" Width (decimal) 35.75 Net Depth with Door Handle 28 6/8" Product Dimensions with Door without Handles 35 3/4" (W) x 70" (H) x 28 3/4" (D
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-11
Visually labeled 90-degree front-to-back envelope in the dimension drawing. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Visually labeled 90-degree front-to-back envelope in the dimension drawing. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Samsung measurement source — rf23bb860012aa + side gap from the maker's document appliancehomestore.com
Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Value used by ExactFit
36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375
Confidence label: medium.
Primary evidence
Samsung measurement source — rf23bb860012aa + side gap from the maker's document appliancehomestore.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on Reviewed: 2026-09-04
Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.
Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Samsung measurement source — 62058011-manufacturer's-brochure.pdf www.nfm.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 2.0 in. Reviewed: 2026-09-05
Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 2.0 in.
Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf appliancehomestore.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-29
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf appliancehomestore.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-29
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Samsung measurement source — 62058011-manufacturer's-brochure.pdf www.nfm.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 2 copy/copies, 1 domain(s Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence
Confidence label: high.
Primary evidence
Samsung measurement source — 62058011-manufacturer's-brochure.pdf www.nfm.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: full-page adjudication=2.0; parser candidates=[1.0, 2.0]; 1" minimum clearance at rear Reviewed: 2026-09-05
full-page adjudication=2.0; parser candidates=[1.0, 2.0]; 1" minimum clearance at rear
full-page adjudication=2.0; parser candidates=[1.0, 2.0]; 1" minimum clearance at rear
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — 934032dda61e446bac8f0631e530355b062030012460ab15f0777b4acbc6df9c.pdf www.nfm.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-15
Will-it-fit sheet "MODEL RF23BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Will-it-fit sheet "MODEL RF23BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Other evidence found
2.5 in — superseded
www.nfm.com; location not retained. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Allow 2.5" of clearance on hinge side. The final reviewed registry supersedes this earlier audit value.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Samsung measurement source — RF23BB8600_V13.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-11
Visually labeled cabinet/product width on the dimension drawing. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Visually labeled cabinet/product width on the dimension drawing. Family bridge: RF23BB86004MAA is the finish/market-suffix variant of RF23BB8600QLAA; shared high-confidence endpoints match.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Selected: 3.75 in. Earlier retained values: 2.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Will-it-fit sheet "MODEL RF23BB8600 DIMENSIONS": "Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall." The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Source documents and pages
Samsung measurement source — RF23BB8600_V13.pdf
Samsung · Web source · exact model/source
Model numbers covered: RF23BB86004MAA. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
6 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
