Measurement evidence for Samsung RF22A4221SRAA

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions width with hinges and doors.

Why this value was used

Product Dimensions width with hinges and doors.

Other evidence found

• 29.88 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Net Width: 29.88 in | n (WxHxD) 29.9 x 66.8 x 34.9 inch - Net Dimension (WxHxD) 759 x 1694 x 886 mm - Net Width (inch) 29.88 inch - Net Case Height with Hinge 66.75 inch - Net Case Height without Hinge 65.5 . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

65.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions height without hinges and door.

Why this value was used

Product Dimensions height without hinges and door.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf4500a-french-door-refrigerator-dispensor-22-cu-ft-silver-rf22a4221sr-aa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height with Hinge: 66.75 in | Net Dimension (WxHxD) 759 x 1694 x 886 mm Net Width (inch) 29.88 inch
Reviewed: 2026-09-04

Height with Hinge: 66.75 in | Net Dimension (WxHxD) 759 x 1694 x 886 mm Net Width (inch) 29.88 inch Net Case Height with Hinge 66.75 inch Net Case Height without Hinge 65.5 inch Net Depth with Door Handle 34.88 inch

Why this value was used

Height with Hinge: 66.75 in | Net Dimension (WxHxD) 759 x 1694 x 886 mm Net Width (inch) 29.88 inch Net Case Height with Hinge 66.75 inch Net Case Height without Hinge 65.5 inch Net Depth with Door Handle 34.88 inch

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf4500a-french-door-refrigerator-dispensor-22-cu-ft-silver-rf22a4221sr-aa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door = 30.625 in | th with Door Handle 34.88 inch - Net Depth without Door Handle 34.8
Reviewed: 2026-09-04

Depth without Door = 30.625 in | th with Door Handle 34.88 inch - Net Depth without Door Handle 34.88 inch - Net Depth without Door 30.63 inch - Packing Dimension (WxHxD) 30 1/2" x 71 7/8" x 36 2/8" - Net Weight (kg) 103 | cached support: samsung.com

Why this value was used

Depth without Door = 30.625 in | th with Door Handle 34.88 inch - Net Depth without Door Handle 34.88 inch - Net Depth without Door 30.63 inch - Packing Dimension (WxHxD) 30 1/2" x 71 7/8" x 36 2/8" - Net Weight (kg) 103 | cached support: samsung.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions closed depth without a projecting handle.

Why this value was used

Product Dimensions closed depth without a projecting handle.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions closed maximum depth including the shown handle configuration.

Why this value was used

Product Dimensions closed maximum depth including the shown handle configuration.

Other evidence found

• 34.88 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Depth with Door Handle: 34.88 in | se Height with Hinge 66.75 inch - Net Case Height without Hinge 65.5 inch - Net Depth with Door Handle 34.88 inch - Net Depth without Door Handle 34.88 inch - Net Depth without Door 30.63 inc. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

46.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Visually labeled 90-degree front-to-back envelope in the dimension drawing.

Why this value was used

Visually labeled 90-degree front-to-back envelope in the dimension drawing.

Other evidence found

• 46.38 in — superseded

  www.fergusonhome.com; location not retained. Model scope: not separately recorded. Raw value: Exact-model cached Dimensions and Measurements table: Depth with Door Open = 46.38 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 29.875 + 2 * 0.375

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Closed product width plus the explicitly required clearance at each side.

Why this value was used

Closed product width plus the explicitly required clearance at each side. Calculation or inference: 29.875 + 2 * 0.375.

Other evidence found

• 30.63 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 30.63 in from product width 29.88 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 66.75 + 0.375

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Height with hinges plus the explicitly required top clearance.

Why this value was used

Height with hinges plus the explicitly required top clearance. Calculation or inference: 66.75 + 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 30.625 + 2

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Case depth without door plus the explicitly required rear clearance.

Why this value was used

Case depth without door plus the explicitly required rear clearance. Calculation or inference: 30.625 + 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_spec-sheet.pdf
web.archive.org · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_spec-sheet.pdf
web.archive.org · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_spec-sheet.pdf
web.archive.org · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top
Reviewed: 2026-09-05

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Why this value was used

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_spec-sheet.pdf
web.archive.org · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow 2" minimum clearance at rear
Reviewed: 2026-09-05

Cached exact-model result: Allow 2" minimum clearance at rear

Why this value was used

Cached exact-model result: Allow 2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105583845.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 17
Reviewed: 2026-10-13

When you install the refrigerator next to a fixed wall, provide a minimum clearance of 3 3/4" (95 mm) to allow the door to swing open; the largest printed door-swing clearance is stored (rule used since batch 13).

Why this value was used

When you install the refrigerator next to a fixed wall, provide a minimum clearance of 3 3/4" (95 mm) to allow the door to swing open; the largest printed door-swing clearance is stored (rule used since batch 13).

Other evidence found

• 1.5 in — superseded

  image-stgus.samsung.com; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 1.5 in clearance on hinge side when installing next to a wall.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF22A4221SR_V5.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Visually labeled cabinet/product width on the dimension drawing.

Why this value was used

Visually labeled cabinet/product width on the dimension drawing.

Other evidence found

• 29 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: case_width_in = 29.0 in; source_id=29006. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.