This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-14. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 48 in | ✓ Conflicting sources — resolved | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit48 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: width_doors_closed_in = 48 in.Open original source ↗ Why this value was usedValidated Monogram specification value: width_doors_closed_in = 48 in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5 in | ✓ Conflicting sources — resolved | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: height_case_in = 83.5 in.Open original source ↗ Why this value was usedValidated Monogram specification value: height_case_in = 83.5 in. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ✓ Verified — retained secondary source | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: height_hinge_in = 84 in.Open original source ↗ Why this value was usedValidated Monogram specification value: height_hinge_in = 84 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.5 in | ✓ Verified — retained secondary source | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit23.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: depth_case_only_in = 23.5 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_case_only_in = 23.5 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 25.75 in | ✓ Conflicting sources — resolved | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit25.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: depth_less_handles_in = 25.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_less_handles_in = 25.75 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.375 in | ✓ Conflicting sources — resolved | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: depth_with_handles_in = 28.375 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_with_handles_in = 28.375 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 52.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Monogram measurement source — ZISS480DNSS_104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit52.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: published case depth + published Door Clearance at 90 degrees Confidence label: high. Primary evidenceMonogram measurement source — ZISS480DNSS_104289934.pdf Exact-model Monogram dimensional page visually prints the mapped depth_doors_open_90_in endpoint as 52.125 in.Open original source ↗ Why this value was usedExact-model Monogram dimensional page visually prints the mapped depth_doors_open_90_in endpoint as 52.125 in. Calculation or inference: published case depth + published Door Clearance at 90 degrees. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 47.5 in | ✓ Verified — retained secondary source | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit47.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: min_cutout_width_in = 47.5 in.Open original source ↗ Why this value was usedValidated Monogram specification value: min_cutout_width_in = 47.5 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Monogram measurement source — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — 104289934.pdf Manufacturer specification gives nominal cutout height 84 in with +/- 1/2 in adjustment range.Open original source ↗ Why this value was usedManufacturer specification gives nominal cutout height 84 in with +/- 1/2 in adjustment range. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Verified — retained secondary source | Monogram measurement source — ZISS480DNSS_104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — ZISS480DNSS_104289934.pdf Exact-model Monogram dimensional page visually prints the mapped min_cutout_depth_in endpoint as 24 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Monogram dimensional page visually prints the mapped min_cutout_depth_in endpoint as 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.25 in | ✓ Verified — retained secondary source | Monogram measurement source — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Primary evidenceMonogram measurement source — 104289934.pdf Cutout is 1/2 in wider than the cabinet body, giving 1/4 in per side.Open original source ↗ Why this value was usedCutout is 1/2 in wider than the cabinet body, giving 1/4 in per side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.25 in | ✓ Verified — retained secondary source | Monogram measurement source — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Primary evidenceMonogram measurement source — 104289934.pdf Cutout is 1/2 in wider than the cabinet body, giving 1/4 in per side.Open original source ↗ Why this value was usedCutout is 1/2 in wider than the cabinet body, giving 1/4 in per side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — retained secondary source | Monogram measurement source — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: nominal min_cutout_height_in - height_hinge_in Confidence label: high. Primary evidenceMonogram measurement source — 104289934.pdf Nominal 84 in cutout equals the 84 in highest appliance endpoint; adjustment range is handled by leveling.Open original source ↗ Why this value was usedNominal 84 in cutout equals the 84 in highest appliance endpoint; adjustment range is handled by leveling. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.5 in | ✓ Verified — retained secondary source | Monogram measurement source — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: high. Primary evidenceMonogram measurement source — 104289934.pdf 24 in cutout minus 23 1/2 in cabinet depth = 1/2 in behind the case.Open original source ↗ Why this value was used24 in cutout minus 23 1/2 in cabinet depth = 1/2 in behind the case. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.625 in | ✓ Verified — retained secondary source | Monogram measurement source — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit4.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceMonogram measurement source — 104289934.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 18.9375 in | ? Verified — finalized database measurement | Monogram measurement source — 104289934.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit18.9375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — 104289934.pdf 18 15/16 in printed for left door fully open to the printed 130 degree position (larger of the printed per-door / standard-installation figures, owner rule). Read by the verification agent (run D5a8175afa9) from a document naming the model. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used18 15/16 in printed for left door fully open to the printed 130 degree position (larger of the printed per-door / standard-installation figures, owner rule). Read by the verification agent (run D5a8175afa9) from a document naming the model. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 47 in | ✓ Conflicting sources — resolved | Monogram installation document — 104289934.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit47 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104289934.pdf Validated Monogram specification value: case_width_in = 47 in.Open original source ↗ Why this value was usedValidated Monogram specification value: case_width_in = 47 in. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 48 in. Earlier retained values: 28.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: width_doors_closed_in = 48 in.
View source scope, location, and impact on fitSelected: 83.5 in. Earlier retained values: 84 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: height_case_in = 83.5 in.
View source scope, location, and impact on fitSelected: 25.75 in. Earlier retained values: 23.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: depth_less_handles_in = 25.75 in.
View source scope, location, and impact on fitSelected: 28.375 in. Earlier retained values: 25.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: depth_with_handles_in = 28.375 in.
View source scope, location, and impact on fitSelected: 47 in. Earlier retained values: 28.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: case_width_in = 47 in.
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: ZISS480DNSS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Minimum cutout width; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: ZISS480DNSS. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
2 displayed measurements supported: Depth with doors open at 90°; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-14. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.