This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 36 in | ✓ Conflicting sources — resolved | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: width_doors_closed_in = 36 in.Open original source ↗ Why this value was usedValidated Monogram specification value: width_doors_closed_in = 36 in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5 in | ✓ Conflicting sources — resolved | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: height_case_in = 83.5 in.Open original source ↗ Why this value was usedValidated Monogram specification value: height_case_in = 83.5 in. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ✓ Verified — retained secondary source | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: height_hinge_in = 84 in.Open original source ↗ Why this value was usedValidated Monogram specification value: height_hinge_in = 84 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.5 in | ✓ Verified — retained secondary source | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit23.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: depth_case_only_in = 23.5 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_case_only_in = 23.5 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 25.75 in | ✓ Verified — retained secondary source | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit25.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: depth_less_handles_in = 25.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_less_handles_in = 25.75 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27.875 in | ✓ Conflicting sources — resolved | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit27.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: depth_with_handles_in = 27.875 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_with_handles_in = 27.875 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 44.0625 in | ✓ Verified — retained secondary source · Calculated/inferred | Monogram measurement source — ZISS360DNSS-105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit44.0625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: published case depth + published Door Clearance at 90 degrees Confidence label: high. Primary evidenceMonogram measurement source — ZISS360DNSS-105166046.pdf Exact-model Monogram dimensional page visually prints the mapped depth_doors_open_90_in endpoint as 44.0625 in.Open original source ↗ Why this value was usedExact-model Monogram dimensional page visually prints the mapped depth_doors_open_90_in endpoint as 44.0625 in. Calculation or inference: published case depth + published Door Clearance at 90 degrees. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.5 in | ✓ Verified — retained secondary source | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: min_cutout_width_in = 35.5 in.Open original source ↗ Why this value was usedValidated Monogram specification value: min_cutout_width_in = 35.5 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Monogram measurement source — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — 105166046.pdf Manufacturer specification gives nominal cutout height 84 in with +/- 1/2 in adjustment range.Open original source ↗ Why this value was usedManufacturer specification gives nominal cutout height 84 in with +/- 1/2 in adjustment range. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Verified — retained secondary source | Monogram measurement source — ZISS360DNSS-105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — ZISS360DNSS-105166046.pdf Exact-model Monogram dimensional page visually prints the mapped min_cutout_depth_in endpoint as 24 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Monogram dimensional page visually prints the mapped min_cutout_depth_in endpoint as 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.25 in | ✓ Verified — retained secondary source | Monogram measurement source — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Primary evidenceMonogram measurement source — 105166046.pdf Cutout is 1/2 in wider than the cabinet body, giving 1/4 in per side.Open original source ↗ Why this value was usedCutout is 1/2 in wider than the cabinet body, giving 1/4 in per side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.25 in | ✓ Verified — retained secondary source | Monogram measurement source — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Primary evidenceMonogram measurement source — 105166046.pdf Cutout is 1/2 in wider than the cabinet body, giving 1/4 in per side.Open original source ↗ Why this value was usedCutout is 1/2 in wider than the cabinet body, giving 1/4 in per side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — retained secondary source | Monogram measurement source — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: nominal min_cutout_height_in - height_hinge_in Confidence label: high. Primary evidenceMonogram measurement source — 105166046.pdf Nominal 84 in cutout equals the 84 in highest appliance endpoint; adjustment range is handled by leveling.Open original source ↗ Why this value was usedNominal 84 in cutout equals the 84 in highest appliance endpoint; adjustment range is handled by leveling. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.5 in | ✓ Verified — retained secondary source | Monogram measurement source — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: high. Primary evidenceMonogram measurement source — 105166046.pdf 24 in cutout minus 23 1/2 in cabinet depth = 1/2 in behind the case.Open original source ↗ Why this value was used24 in cutout minus 23 1/2 in cabinet depth = 1/2 in behind the case. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.125 in | ✓ Verified — retained secondary source | Monogram measurement source — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit4.125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceMonogram measurement source — 105166046.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35 in | ✓ Conflicting sources — resolved | Monogram installation document — 105166046.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 105166046.pdf Validated Monogram specification value: case_width_in = 35 in.Open original source ↗ Why this value was usedValidated Monogram specification value: case_width_in = 35 in. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 36 in. Earlier retained values: 20.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: width_doors_closed_in = 36 in.
View source scope, location, and impact on fitSelected: 83.5 in. Earlier retained values: 84 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: height_case_in = 83.5 in.
View source scope, location, and impact on fitSelected: 27.875 in. Earlier retained values: 25.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: depth_with_handles_in = 27.875 in.
View source scope, location, and impact on fitSelected: 35 in. Earlier retained values: 20.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: case_width_in = 35 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: ZISS360DNSS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
14 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Minimum cutout width; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: ZISS360DNSS. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
2 displayed measurements supported: Depth with doors open at 90°; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.