This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.5625 in | ✓ Secondary source only | Monogram ZIR361NPRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit35.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIR361NPRII Quick Specs Overall Width 35 9/16"Open original source ↗ Why this value was usedOverall Width 35 9/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.375 in | ✓ Conflicting sources — resolved · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit83.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs Validated Monogram specification value: height_case_in = 83.375 in.Open original source ↗ Why this value was usedValidated Monogram specification value: height_case_in = 83.375 in. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Cabinet height. Relevant equivalence evidence: Validated Monogram specification value: height_case_in = 83.375 in.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.5 in | ✓ Secondary source only | Monogram ZIR361NPRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIR361NPRII Quick Specs Overall Height 83 1/2"Open original source ↗ Why this value was usedOverall Height 83 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 22.25 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit22.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs Validated Monogram specification value: depth_case_only_in = 22.25 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_case_only_in = 22.25 in. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Depth without door. Relevant equivalence evidence: Validated Monogram specification value: depth_case_only_in = 22.25 in.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs Validated Monogram specification value: depth_less_handles_in = 24.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_less_handles_in = 24.75 in. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Depth with door, without handles. Relevant equivalence evidence: Validated Monogram specification value: depth_less_handles_in = 24.75 in.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27.3125 in | ✓ Conflicting sources — resolved · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit27.3125 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 2 9/16 in Statement handle projection Confidence label: medium. Calculation inputs: Depth with door, without handles; Primary evidenceMonogram ZIR361NBRII Quick Specs Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.Open original source ↗ Why this value was usedManufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety. Calculation or inference: depth_less_handles_in + 2 9/16 in Statement handle projection. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: depth_less_handles_in + 2 9/16 in Statement handle projection. Measurement transferred: Depth with handle. Relevant equivalence evidence: Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.. Known differences: not separately recorded. Review decision: calculated formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 39.375 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit39.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs Exact-model manufacturer specification lists Door Clearance at 90 degrees for the current NBR/PR hinge generation.Open original source ↗ Why this value was usedExact-model manufacturer specification lists Door Clearance at 90 degrees for the current NBR/PR hinge generation. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Depth with doors open at 90°. Relevant equivalence evidence: Exact-model manufacturer specification lists Door Clearance at 90 degrees for the current NBR/PR hinge generation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.8125 in | ✓ Secondary source only | Monogram ZIR361NPRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit35.8125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIR361NPRII Quick Specs Cutout Width 35 13/16" (91.0 cm)Open original source ↗ Why this value was usedCutout Width 35 13/16" (91.0 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Secondary source only | Monogram ZIR361NPRII Mixed Product Triple Installation assets.skulytics.io | Page 3 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIR361NPRII Mixed Product Triple Installation 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" | 3. Cabinet cutout interior surfaces should be fully finished to a minimum depth of 6"Open original source ↗ Why this value was used1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" | 3. Cabinet cutout interior surfaces should be fully finished to a minimum depth of 6" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Secondary source only | Monogram ZIR361NPRII Mixed Product Triple Installation assets.skulytics.io | Page 3 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIR361NPRII Mixed Product Triple Installation installations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84"Open original source ↗ Why this value was usedinstallations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width NBR/NPN/NPR integrated-column chassis Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side.Open original source ↗ Why this value was usedFinished cutout is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: same-width NBR/NPN/NPR integrated-column chassis. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: same-width NBR/NPN/NPR integrated-column chassis. Measurement transferred: Left-side ventilation clearance. Relevant equivalence evidence: Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side.. Known differences: not separately recorded. Review decision: documented handle finish chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width NBR/NPN/NPR integrated-column chassis Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side.Open original source ↗ Why this value was usedFinished cutout is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: same-width NBR/NPN/NPR integrated-column chassis. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: same-width NBR/NPN/NPR integrated-column chassis. Measurement transferred: Right-side ventilation clearance. Relevant equivalence evidence: Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side.. Known differences: not separately recorded. Review decision: documented handle finish chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Secondary source only · Calculated/inferred | Monogram measurement source — https://www.abcwarehouse.com/monogram-zir361nbrii www.abcwarehouse.com | Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Monogram ZIR361NBRII; original evi | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Monogram ZIR361NBRII Confidence label: medium. Primary evidenceMonogram measurement source — https://www.abcwarehouse.com/monogram-zir361nbrii Conflict-free corporate-family exact 8-dimension chassis match to Monogram ZIR361NBRII; original evidence: Top Air Clearances, 0.5 inOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Monogram ZIR361NBRII; original evidence: Top Air Clearances, 0.5 in Calculation or inference: exact 8-dimension chassis signature; source model Monogram ZIR361NBRII. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.25 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width NBR/NPN/NPR integrated-column chassis Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs 25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in.Open original source ↗ Why this value was used25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in. Calculation or inference: same-width NBR/NPN/NPR integrated-column chassis. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: same-width NBR/NPN/NPR integrated-column chassis. Measurement transferred: Rear clearance. Relevant equivalence evidence: 25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in.. Known differences: not separately recorded. Review decision: documented handle finish chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | Unknown | ? Not found | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIR361NBRII Quick Specs Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 4.562 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.5625 in | ✓ Secondary source only | Monogram ZIR361NPRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit35.5625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIR361NPRII Quick Specs Overall Width 35 9/16"Open original source ↗ Why this value was usedOverall Width 35 9/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 4.5625 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIR361NBRII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit4.5625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIR361NBRII Quick Specs Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.Open original source ↗ Why this value was usedManufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIR361NBRII appliesTarget model: ZIR361NPRII. Supporting model: ZIR361NBRII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Adjoining-wall clearance (reviewed endpoint). Relevant equivalence evidence: Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 83.375 in. Earlier retained values: 83.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: height_case_in = 83.375 in. Calculation or inference: conflict-free shared-chassis propagation.
View source scope, location, and impact on fitSelected: 27.3125 in. Earlier retained values: 24.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety. Calculation or inference: depth_less_handles_in + 2 9/16 in Statement handle projection.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: 104295915.pdf. Related-model record: ZIR361NBRII.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Quick Specs · secondary model/source
Model numbers covered: ZIR361NPRII. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Overall width; Height with hinge / controlling height; Minimum cutout width; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Quick Specs · equivalent model/source
Model numbers covered: ZIR361NBRII. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
10 displayed measurements supported: Cabinet height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Mixed Product Triple Installation · secondary model/source
Model numbers covered: ZIR361NPRII. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.abcwarehouse.com · Web source · secondary model/source
Model numbers covered: ZIR361NPRII. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.