Measurement evidence for Monogram ZIR301NPNII

Value used by ExactFit

29.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIR301NPNII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Width 29 9/16"

Why this value was used

Overall Width 29 9/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Validated Monogram specification value: height_case_in = 83.375 in.

Why this value was used

Validated Monogram specification value: height_case_in = 83.375 in. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

• 83.5 in — superseded

  105165943.pdf (p.5); page 5. Model scope: not separately recorded. Raw value: Overall Height -> 83 1/2" (212.1 cm). The final reviewed registry supersedes this earlier audit value. Validated Monogram specification value: height_case_in = 83.375 in.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIR301NPNII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Height 83 1/2"

Why this value was used

Overall Height 83 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Validated Monogram specification value: depth_case_only_in = 22.25 in.

Why this value was used

Validated Monogram specification value: depth_case_only_in = 22.25 in. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

• 23.875 in — superseded

  https://www.appliancepalace.com/products/monogram-zir301npnii.html; location not retained. Model scope: not separately recorded. Raw value: Case Depth = 23.875 in | MONOGRAM ZIR301NPNII Specifications ; Case Depth Without Door. 23.875 in ; Cutout Depth (in). 25 in ; Depth Without Handle. 23.875 in ; Cutout Height (i. The final reviewed registry supersedes this earlier audit value. Validated Monogram specification value: depth_case_only_in = 22.25 in.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Validated Monogram specification value: depth_less_handles_in = 24.75 in.

Why this value was used

Validated Monogram specification value: depth_less_handles_in = 24.75 in. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

• 23.875 in — superseded

  https://www.appliancepalace.com/products/monogram-zir301npnii.html; location not retained. Model scope: not separately recorded. Raw value: Depth Without Handle = 23.875 in | pecifications ; Case Depth Without Door. 23.875 in ; Cutout Depth (in). 25 in ; Depth Without Handle. 23.875 in ; Cutout Height (in). 84 in ; Cabinet Width. 30 in. . The final reviewed registry supersedes this earlier audit value. Validated Monogram specification value: depth_less_handles_in = 24.75 in.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.3125 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 2 9/16 in Statement handle projection

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.

Why this value was used

Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety. Calculation or inference: depth_less_handles_in + 2 9/16 in Statement handle projection.

Other evidence found

• 24.75 in — superseded

  105165941.pdf; page 2. Model scope: not separately recorded. Raw value: Overall Depth 24 3/4" (62.9 cm). The final reviewed registry supersedes this earlier audit value. Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

55.625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram measurement source — https://device.report/monogram/zir301
device.report · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model archived specification: Depth With Door 90 Degrees Open 55 5/8 in.
Reviewed: 2026-09-04

Exact-model archived specification: Depth With Door 90 Degrees Open 55 5/8 in.

Why this value was used

Exact-model archived specification: Depth With Door 90 Degrees Open 55 5/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIR301NPNII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Cutout Width 29 13/16" (75.7 cm)

Why this value was used

Cutout Width 29 13/16" (75.7 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIR301NPNII Mixed Product Triple Installation
assets.skulytics.io · Mixed Product Triple Installation
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" | 3. Cabinet cutout interior surfaces should be fully finished to a minimum depth of 6"

Why this value was used

1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" | 3. Cabinet cutout interior surfaces should be fully finished to a minimum depth of 6"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIR301NPNII Mixed Product Triple Installation
assets.skulytics.io · Mixed Product Triple Installation
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

installations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84"

Why this value was used

installations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-width NBR/NPN/NPR integrated-column chassis

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: same-width NBR/NPN/NPR integrated-column chassis.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-width NBR/NPN/NPR integrated-column chassis

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Finished cutout is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: same-width NBR/NPN/NPR integrated-column chassis.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-width NBR/NPN/NPR integrated-column chassis

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

84 in cutout minus 83 1/2 in highest appliance endpoint = 1/2 in.

Why this value was used

84 in cutout minus 83 1/2 in highest appliance endpoint = 1/2 in. Calculation or inference: same-width NBR/NPN/NPR integrated-column chassis.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-width NBR/NPN/NPR integrated-column chassis

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in.

Why this value was used

25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in. Calculation or inference: same-width NBR/NPN/NPR integrated-column chassis.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 4.562 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.5625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIR301NPNII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Width 29 9/16"

Why this value was used

Overall Width 29 9/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

4.5625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIR301NBRII Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.

Why this value was used

Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.