This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Secondary source only | Monogram ZIP364NBVII Retrofit Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIP364NBVII Retrofit Quick Specs Overall Width 35 3/4"Open original source ↗ Why this value was usedOverall Width 35 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.6875 in | ✓ Conflicting sources — resolved · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit83.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs Validated Monogram specification value: height_case_in = 83.6875 in.Open original source ↗ Why this value was usedValidated Monogram specification value: height_case_in = 83.6875 in. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Cabinet height. Relevant equivalence evidence: Validated Monogram specification value: height_case_in = 83.6875 in.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.875 in | ✓ Secondary source only | Monogram ZIP364NBVII Retrofit Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit83.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIP364NBVII Retrofit Quick Specs Overall Height 83 7/8"Open original source ↗ Why this value was usedOverall Height 83 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 22.125 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit22.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs Validated Monogram specification value: depth_case_only_in = 22.125 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_case_only_in = 22.125 in. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Depth without door. Relevant equivalence evidence: Validated Monogram specification value: depth_case_only_in = 22.125 in.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs Validated Monogram specification value: depth_less_handles_in = 24.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_less_handles_in = 24.75 in. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Depth with door, without handles. Relevant equivalence evidence: Validated Monogram specification value: depth_less_handles_in = 24.75 in.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27.3125 in | ✓ Conflicting sources — resolved · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit27.3125 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 2 9/16 in Statement handle projection Confidence label: medium. Calculation inputs: Depth with door, without handles; Primary evidenceMonogram ZIP364IPVII Quick Specs Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.Open original source ↗ Why this value was usedManufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety. Calculation or inference: depth_less_handles_in + 2 9/16 in Statement handle projection. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: depth_less_handles_in + 2 9/16 in Statement handle projection. Measurement transferred: Depth with handle. Relevant equivalence evidence: Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.. Known differences: not separately recorded. Review decision: calculated formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 46.375 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit46.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs Manufacturer diagram/cached exact-model specifications give depth with door open 90 degrees as 46 3/8 in.Open original source ↗ Why this value was usedManufacturer diagram/cached exact-model specifications give depth with door open 90 degrees as 46 3/8 in. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Depth with doors open at 90°. Relevant equivalence evidence: Manufacturer diagram/cached exact-model specifications give depth with door open 90 degrees as 46 3/8 in.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Secondary source only | Monogram ZIP364NBVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIP364NBVII Quick Specs Cutout Width 36" (91.4 cm)Open original source ↗ Why this value was usedCutout Width 36" (91.4 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Secondary source only | Monogram ZIP364NBVII Mixed Product Triple Installation assets.skulytics.io | Page 3 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIP364NBVII Mixed Product Triple Installation 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" | 3. Cabinet cutout interior surfaces should be fully finished to a minimum depth of 6"Open original source ↗ Why this value was used1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" | 3. Cabinet cutout interior surfaces should be fully finished to a minimum depth of 6" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Secondary source only | Monogram ZIP364NBVII Mixed Product Triple Installation assets.skulytics.io | Page 3 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIP364NBVII Mixed Product Triple Installation installations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84"Open original source ↗ Why this value was usedinstallations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs 36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side.Open original source ↗ Why this value was used36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: same documented 36-inch integrated chassis; hinge/finish variant. Measurement transferred: Left-side ventilation clearance. Relevant equivalence evidence: 36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side.. Known differences: not separately recorded. Review decision: documented chassis hinge finish propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs 36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side.Open original source ↗ Why this value was used36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: same documented 36-inch integrated chassis; hinge/finish variant. Measurement transferred: Right-side ventilation clearance. Relevant equivalence evidence: 36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side.. Known differences: not separately recorded. Review decision: documented chassis hinge finish propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.125 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs 84 in cutout minus 83 7/8 in highest appliance endpoint = 1/8 in.Open original source ↗ Why this value was used84 in cutout minus 83 7/8 in highest appliance endpoint = 1/8 in. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: same documented 36-inch integrated chassis; hinge/finish variant. Measurement transferred: Top clearance. Relevant equivalence evidence: 84 in cutout minus 83 7/8 in highest appliance endpoint = 1/8 in.. Known differences: not separately recorded. Review decision: documented chassis hinge finish propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.25 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs 25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in.Open original source ↗ Why this value was used25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: same documented 36-inch integrated chassis; hinge/finish variant. Measurement transferred: Rear clearance. Relevant equivalence evidence: 25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in.. Known differences: not separately recorded. Review decision: documented chassis hinge finish propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | Unknown | ? Not found | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIP364IPVII Quick Specs Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 4.562 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Secondary source only | Monogram ZIP364NBVII Retrofit Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram ZIP364NBVII Retrofit Quick Specs Overall Width 35 3/4"Open original source ↗ Why this value was usedOverall Width 35 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 4.5625 in | ✓ Verified — equivalent model · Calculated/inferred | Monogram ZIP364IPVII Quick Specs assets.skulytics.io | Page 2 | |
Value used by ExactFit4.5625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation Confidence label: medium. Primary evidenceMonogram ZIP364IPVII Quick Specs Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.Open original source ↗ Why this value was usedManufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing. Calculation or inference: conflict-free shared-chassis propagation. Why evidence from ZIP364IPVII appliesTarget model: ZIP364NBVII. Supporting model: ZIP364IPVII. Manufacturer: Monogram. Product family and measurement relationship: conflict-free shared-chassis propagation. Measurement transferred: Adjoining-wall clearance (reviewed endpoint). Relevant equivalence evidence: Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 83.6875 in. Earlier retained values: 83.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Validated Monogram specification value: height_case_in = 83.6875 in. Calculation or inference: conflict-free shared-chassis propagation.
View source scope, location, and impact on fitSelected: 27.3125 in. Earlier retained values: 24.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety. Calculation or inference: depth_less_handles_in + 2 9/16 in Statement handle projection.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: 104296165.pdf. Related-model record: ZIP364IPVII.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Retrofit Quick Specs · secondary model/source
Model numbers covered: ZIP364NBVII. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
3 displayed measurements supported: Overall width; Height with hinge / controlling height; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Quick Specs · equivalent model/source
Model numbers covered: ZIP364IPVII. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
11 displayed measurements supported: Cabinet height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Quick Specs · secondary model/source
Model numbers covered: ZIP364NBVII. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Mixed Product Triple Installation · secondary model/source
Model numbers covered: ZIP364NBVII. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.