This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-15. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.75 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Validated Monogram specification value: width_doors_closed_in = 29.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: width_doors_closed_in = 29.75 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 80.375 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit80.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Validated Monogram specification value: height_case_in = 80.375 in.Open original source ↗ Why this value was usedValidated Monogram specification value: height_case_in = 80.375 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 79.375 in | ✓ Conflicting sources — resolved | Monogram measurement source — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit79.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — 104290893.pdf Overall height adjustable from 79 3/8" to 80 3/8". Height is stored with the leveling legs at their lowest setting, as for other models (the range top was stored before).Open original source ↗ Why this value was usedOverall height adjustable from 79 3/8" to 80 3/8". Height is stored with the leveling legs at their lowest setting, as for other models (the range top was stored before). Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.75 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit23.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Validated Monogram specification value: depth_case_only_in = 23.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_case_only_in = 23.75 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 23.75 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit23.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Validated Monogram specification value: depth_less_handles_in = 23.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_less_handles_in = 23.75 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 23.75 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit23.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Validated Monogram specification value: depth_with_handles_in = 23.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: depth_with_handles_in = 23.75 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 36.75 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit36.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Manufacturer specification lists Door Clearance at 90 degrees as 36 3/4 in.Open original source ↗ Why this value was usedManufacturer specification lists Door Clearance at 90 degrees as 36 3/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Validated Monogram specification value: min_cutout_width_in = 30 in.Open original source ↗ Why this value was usedValidated Monogram specification value: min_cutout_width_in = 30 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 80 in | ✓ Verified — retained secondary source | Monogram measurement source — ZIK303NPPII_104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit80 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — ZIK303NPPII_104290893.pdf Exact specification: Cutout Height 80" to 84" depending on door choice; product height adjusts from 79-3/8" to 80-3/8".Open original source ↗ Why this value was usedExact specification: Cutout Height 80" to 84" depending on door choice; product height adjusts from 79-3/8" to 80-3/8". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Monogram measurement source — ZIK303NPPII_104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — ZIK303NPPII_104290893.pdf Exact-model Monogram dimensional page visually prints the mapped min_cutout_depth_in endpoint as 25 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Monogram dimensional page visually prints the mapped min_cutout_depth_in endpoint as 25 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Monogram measurement source — ZIK303NPPII_104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (published cutout width - published closed overall width) / 2; centered installation Confidence label: high. Primary evidenceMonogram measurement source — ZIK303NPPII_104290893.pdf Exact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 0.125 in.Open original source ↗ Why this value was usedExact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 0.125 in. Calculation or inference: (published cutout width - published closed overall width) / 2; centered installation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Monogram measurement source — ZIK303NPPII_104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (published cutout width - published closed overall width) / 2; centered installation Confidence label: high. Primary evidenceMonogram measurement source — ZIK303NPPII_104290893.pdf Exact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 0.125 in.Open original source ↗ Why this value was usedExact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 0.125 in. Calculation or inference: (published cutout width - published closed overall width) / 2; centered installation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — retained secondary source · Calculated/inferred | Monogram measurement source — ZIK303NPPII_104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: published cutout height - published installed overall height Confidence label: high. Primary evidenceMonogram measurement source — ZIK303NPPII_104290893.pdf Exact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 0 in.Open original source ↗ Why this value was usedExact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 0 in. Calculation or inference: published cutout height - published installed overall height. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Monogram measurement source — ZIK303NPPII_104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit1.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: published cutout depth - published overall depth without handle Confidence label: high. Primary evidenceMonogram measurement source — ZIK303NPPII_104290893.pdf Exact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 1.25 in.Open original source ↗ Why this value was usedExact-model Monogram page visually prints both installation and appliance endpoints; retained formula yields 1.25 in. Calculation or inference: published cutout depth - published overall depth without handle. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4 in | ✓ Verified — retained secondary source | Monogram measurement source — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit4 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceMonogram measurement source — 104290893.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 17 in | ? Verified — finalized database measurement | Monogram measurement source — 104290893.pdf Publisher not recorded | Page 7 | |
Value used by ExactFit17 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram measurement source — 104290893.pdf 17 in printed: D641f4056a6 p.7; condition: full factory-set 115-degree door swing; SS or custom panels (larger of the printed figures, owner rule). Read by the verification agent from a document naming the model. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used17 in printed: D641f4056a6 p.7; condition: full factory-set 115-degree door swing; SS or custom panels (larger of the printed figures, owner rule). Read by the verification agent from a document naming the model. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.75 in | ✓ Verified — retained secondary source | Monogram installation document — 104290893.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMonogram installation document — 104290893.pdf Validated Monogram specification value: case_width_in = 29.75 in.Open original source ↗ Why this value was usedValidated Monogram specification value: case_width_in = 29.75 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 79.375 in. Earlier retained values: 80.375 in, 80.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Overall height adjustable from 79 3/8" to 80 3/8". Height is stored with the leveling legs at their lowest setting, as for other models (the range top was stored before).
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: ZIK303NPPII. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
11 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: ZIK303NPPII. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
6 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-15. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.