Measurement evidence for Monogram ZIC363NBVLH

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIC363NBVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Width 35 3/4"

Why this value was used

Overall Width 35 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Validated Monogram specification value: height_case_in = 83.6875 in.

Why this value was used

Validated Monogram specification value: height_case_in = 83.6875 in. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

• 83.875 in — superseded

  104296074.pdf (p.6); page 6. Model scope: not separately recorded. Raw value: Overall Height -> 83 7/8" (213 cm). The final reviewed registry supersedes this earlier audit value. Validated Monogram specification value: height_case_in = 83.6875 in.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIC363NBVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Height 83 7/8"

Why this value was used

Overall Height 83 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Validated Monogram specification value: depth_case_only_in = 22.125 in.

Why this value was used

Validated Monogram specification value: depth_case_only_in = 22.125 in. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

• 22.875 in — superseded

  local-cache chassis consensus; location not retained. Model scope: not separately recorded. Raw value: Monogram ZIC363NBVRH cached left/right-hinge chassis match. The final reviewed registry supersedes this earlier audit value. Validated Monogram specification value: depth_case_only_in = 22.125 in.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Validated Monogram specification value: depth_less_handles_in = 24.75 in.

Why this value was used

Validated Monogram specification value: depth_less_handles_in = 24.75 in. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

• 22.875 in — superseded

  local-cache chassis consensus; location not retained. Model scope: not separately recorded. Raw value: Monogram ZIC363NBVRH cached left/right-hinge chassis match. The final reviewed registry supersedes this earlier audit value. Validated Monogram specification value: depth_less_handles_in = 24.75 in.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.3125 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 2 9/16 in Statement handle projection

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.

Why this value was used

Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety. Calculation or inference: depth_less_handles_in + 2 9/16 in Statement handle projection.

Other evidence found

• 24.75 in — superseded

  104296068.pdf; page 2. Model scope: not separately recorded. Raw value: Overall Depth 24 3/4" (62.9 cm). The final reviewed registry supersedes this earlier audit value. Manufacturer diagram states that the Statement handle adds 2 9/16 in depth; the larger documented handle option is used for fit safety.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

61.6875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Manufacturer side view gives total 90-degree/open depth 61 11/16 in; 39 9/16 in is the separate open-width dimension.

Why this value was used

Manufacturer side view gives total 90-degree/open depth 61 11/16 in; 39 9/16 in is the separate open-width dimension. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIC363NBVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Cutout Width 36" (91.4 cm)

Why this value was used

Cutout Width 36" (91.4 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIC363NBVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Cutout Height | 84" (213.4 cm) | Cutout Depth

Why this value was used

Cutout Height | 84" (213.4 cm) | Cutout Depth

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIC363NBVLH Mixed Product Triple Installation
assets.skulytics.io · Mixed Product Triple Installation
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

installations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84"

Why this value was used

installations the following requirements apply: | 1. Cabinet cutout depth must be 25" | 2. Cabinet cutout height must be 84"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side.

Why this value was used

36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side.

Why this value was used

36 in cutout minus 35 3/4 in appliance width, divided equally = 1/8 in per side. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

84 in cutout minus 83 7/8 in highest appliance endpoint = 1/8 in.

Why this value was used

84 in cutout minus 83 7/8 in highest appliance endpoint = 1/8 in. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same documented 36-inch integrated chassis; hinge/finish variant

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in.

Why this value was used

25 in cutout minus 24 3/4 in finished handleless appliance depth = 1/4 in. Calculation or inference: same documented 36-inch integrated chassis; hinge/finish variant.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 4.562 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Monogram ZIC363NBVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Width 35 3/4"

Why this value was used

Overall Width 35 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

4.5625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free shared-chassis propagation

Confidence label: medium.

Primary evidence

Monogram ZIC363IPVLH Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing.

Why this value was used

Manufacturer top-view note gives the minimum clearance to an adjacent wall for a 90-degree door swing. Calculation or inference: conflict-free shared-chassis propagation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.