This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.875 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit35.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Appliance width in in.(mm) -> 35 7/8 (910)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 35 7/8 (910) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 79.875 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit79.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Appliance height in in.(mm) -> 79 7/8 (2027)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 79 7/8 (2027) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 79.875 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit79.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Appliance height in in.(mm) -> 79 7/8 (2027)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 79 7/8 (2027) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.125 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit24.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Appliance depth in in.(mm) -> 24 1/8 (610)Open original source ↗ Why this value was usedAppliance depth in in.(mm) -> 24 1/8 (610) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.875 in | ✓ Conflicting sources — resolved · Calculated/inferred | Miele KFNF9959IDE Operating and Installation instructions PDF assets.skulytics.io | Page 23 | |
Value used by ExactFit24.875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24.125-in case + 0.75-in panel Confidence label: medium. Primary evidenceMiele KFNF9959IDE Operating and Installation instructions PDF Standard furniture-panel configuration.Open original source ↗ Why this value was usedStandard furniture-panel configuration. Calculation or inference: 24.125-in case + 0.75-in panel. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 25.875 in | ✓ Secondary source only · Calculated/inferred | Miele KFNF9959IDE Operating and Installation instructions PDF assets.skulytics.io | Page 23 | |
Value used by ExactFit25.875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 1-in handle Confidence label: medium. Calculation inputs: Depth with door, without handles; Primary evidenceMiele KFNF9959IDE Operating and Installation instructions PDF Custom handles vary.Open original source ↗ Why this value was usedCustom handles vary. Calculation or inference: depth_less_handles_in + 1-in handle. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.1875 in | ✓ Secondary source only · Calculated/inferred | Miele KFNF9959IDE Operating and Installation instructions PDF assets.skulytics.io | Page 22 | |
Value used by ExactFit43.1875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 42.4375-in manufacturer open dimension + 0.75-in panel Confidence label: medium. Primary evidenceMiele KFNF9959IDE Operating and Installation instructions PDF Drawing says open-angle value excludes cabinet front and handle.Open original source ↗ Why this value was usedDrawing says open-angle value excludes cabinet front and handle. Calculation or inference: 42.4375-in manufacturer open dimension + 0.75-in panel. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36.125 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit36.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Niche width in inches (mm), min. -> 36 1/8 (915)Open original source ↗ Why this value was usedNiche width in inches (mm), min. -> 36 1/8 (915) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 80 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 1 | |
Value used by ExactFit80 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Exact-model Miele product sheet: minimum niche height 2032 mm; normalized to nearest 1/8 in = 80 in.Open original source ↗ Why this value was usedExact-model Miele product sheet: minimum niche height 2032 mm; normalized to nearest 1/8 in = 80 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24.625 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 1 | |
Value used by ExactFit24.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.625 in; supersedes prior metric-normalized/family value 24.0.Open original source ↗ Why this value was usedExact-model US Miele product sheet explicitly states min_cutout_depth_in=24.625 in; supersedes prior metric-normalized/family value 24.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele KFNF9959IDE Product sheet PDF Per-side cavity reveal derived from verified niche width 36.125 in minus widest closed appliance width 35.875 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 1/8 (915)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 36.125 in minus widest closed appliance width 35.875 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 1/8 (915) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele KFNF9959IDE Product sheet PDF Per-side cavity reveal derived from verified niche width 36.125 in minus widest closed appliance width 35.875 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 1/8 (915)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 36.125 in minus widest closed appliance width 35.875 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 1/8 (915) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: normalized exact-model niche height - max(height_case_in,height_hinge_in) Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Primary evidenceMiele KFNF9959IDE Product sheet PDF Top cavity delta from exact-model sheet: normalized minimum niche height 80 in minus highest verified appliance height 79.875 in = 0.125 in.Open original source ↗ Why this value was usedTop cavity delta from exact-model sheet: normalized minimum niche height 80 in minus highest verified appliance height 79.875 in = 0.125 in. Calculation or inference: normalized exact-model niche height - max(height_case_in,height_hinge_in). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.5 in | ✓ Secondary source only · Calculated/inferred | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: medium. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceMiele KFNF9959IDE Product sheet PDF Recomputed from exact-model US product sheet: 24.625 in niche dimension minus 24.125 in verified appliance dimension = 0.5 in; supersedes prior value 0.5.Open original source ↗ Why this value was usedRecomputed from exact-model US product sheet: 24.625 in niche dimension minus 24.125 in verified appliance dimension = 0.5 in; supersedes prior value 0.5. Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 3 in | ✓ Secondary source only | Miele KFNF9959IDE Operating and Installation instructions PDF assets.skulytics.io | Page 21 | |
Value used by ExactFit3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Operating and Installation instructions PDF Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer drawing dimension A: 3-in adjoining-wall clearance.Open original source ↗ Why this value was usedVerified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer drawing dimension A: 3-in adjoining-wall clearance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.875 in | ✓ Secondary source only | Miele KFNF9959IDE Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit35.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Product sheet PDF Appliance width in in.(mm) -> 35 7/8 (910)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 35 7/8 (910) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 3 in | ✓ Secondary source only | Miele KFNF9959IDE Operating and Installation instructions PDF assets.skulytics.io | Page 21 | |
Value used by ExactFit3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFNF9959IDE Operating and Installation instructions PDF Manufacturer drawing dimension A: 3-in adjoining-wall clearance.Open original source ↗ Why this value was usedManufacturer drawing dimension A: 3-in adjoining-wall clearance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 24.875 in. Earlier retained values: 24.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Standard furniture-panel configuration. Calculation or inference: 24.125-in case + 0.75-in panel.
View source scope, location, and impact on fitassets.skulytics.io · Product sheet PDF · secondary model/source
Model numbers covered: KFNF9959IDE. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Operating and Installation instructions PDF · secondary model/source
Model numbers covered: KFNF9959IDE. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
5 displayed measurements supported: Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product sheet PDF · secondary model/source
Model numbers covered: KFNF9959IDE. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.