Measurement evidence for Miele KFN9855IDE

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524075.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 29 7/8 (757)

Why this value was used

Appliance width in in.(mm) -> 29 7/8 (757)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

79.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524075.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 79 7/8 (2027)

Why this value was used

Appliance height in in.(mm) -> 79 7/8 (2027)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

79.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524075.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 79 7/8 (2027)

Why this value was used

Appliance height in in.(mm) -> 79 7/8 (2027)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524075.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance depth in in.(mm) -> 24 1/8 (610)

Why this value was used

Appliance depth in in.(mm) -> 24 1/8 (610)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24.125-in case + 0.75-in panel

Confidence label: medium.

Primary evidence

Miele measurement source — 74524075.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 65
Reviewed: 2026-09-04

Standard furniture-panel configuration.

Why this value was used

Standard furniture-panel configuration. Calculation or inference: 24.125-in case + 0.75-in panel.

Other evidence found

• 24.125 in — superseded

  Document 74524075.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 1/8 (610). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25.875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 1-in handle

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Miele measurement source — 74524075.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 65
Reviewed: 2026-09-04

Custom handles vary.

Why this value was used

Custom handles vary. Calculation or inference: depth_less_handles_in + 1-in handle.

Other evidence found

• 24 in — superseded

  www.designerappliances.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Depth = 24.0 in | eady Miele KFN9855iDELI 30" Bottom Mount Refrigerator - Left Hinge, Panel Ready ; Height: 79 13/16" ; Depth: 24" ; Size. Full Size ; Type. Built In ; Style. Bottom ...Read more . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

56.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 55.625-in manufacturer open dimension + 0.75-in panel

Confidence label: medium.

Primary evidence

Miele measurement source — 74524075.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 64
Reviewed: 2026-09-04

Drawing says open-angle value excludes cabinet front and handle.

Why this value was used

Drawing says open-angle value excludes cabinet front and handle. Calculation or inference: 55.625-in manufacturer open dimension + 0.75-in panel.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524075.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 30 (762)

Why this value was used

Niche width in inches (mm), min. -> 30 (762)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

80 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Miele measurement source — d4b97b0ed0acb05c8b2b8dc34e593870d4f2fc0e0e993e4657f1804f65b41e83.pdf
Miele · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 25
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 79.875 in plus propagated top clearance 0.125 in.

Why this value was used

Minimum opening height derived from highest appliance endpoint 79.875 in plus propagated top clearance 0.125 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524074.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.125 in; supersedes prior metric-normalized/family value 24.0.

Why this value was used

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.125 in; supersedes prior metric-normalized/family value 24.0.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: medium.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — 74524075.pdf (p.3)
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762)

Why this value was used

Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: medium.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — 74524075.pdf (p.3)
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762)

Why this value was used

Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Miele KFN9859IDE

Confidence label: medium.

Primary evidence

Miele measurement source — d4b97b0ed0acb05c8b2b8dc34e593870d4f2fc0e0e993e4657f1804f65b41e83.pdf
Miele · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 25
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Miele KFN9859IDE; original evidence: Top cavity clearance derived from verified niche height 80 in minus highest appliance height 79.875 in = 0.125 in. Base evidence: opening A Refrigerator door panel B 80"

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Miele KFN9859IDE; original evidence: Top cavity clearance derived from verified niche height 80 in minus highest appliance height 79.875 in = 0.125 in. Base evidence: opening A Refrigerator door panel B 80" Calculation or inference: exact 8-dimension chassis signature; source model Miele KFN9859IDE.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: high.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Miele measurement source — KFN9855iDE-74524074.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database rear_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database rear_clearance_in term. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Miele measurement source — 74524075.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 62
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer drawing dimension A: 3-in adjoining-wall clearance.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer drawing dimension A: 3-in adjoining-wall clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524075.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 29 7/8 (757)

Why this value was used

Appliance width in in.(mm) -> 29 7/8 (757)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.