This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.875 in | ✓ Secondary source only | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit29.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3836R Product sheet PDF Appliance width in in.(mm) -> 29 7/8 (756)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 29 7/8 (756) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.75 in | ✓ Secondary source only | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3836R Product sheet PDF Appliance height in in.(mm) -> 83 3/4 (2125)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 83 3/4 (2125) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.75 in | ✓ Secondary source only | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3836R Product sheet PDF Appliance height in in.(mm) -> 83 3/4 (2125)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 83 3/4 (2125) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Secondary source only | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3836R Product sheet PDF Appliance depth in in.(mm) -> 24 (608)Open original source ↗ Why this value was usedAppliance depth in in.(mm) -> 24 (608) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | Unknown | ? Not found | Miele KFMC3632L Product sheet PDF assets.skulytics.io | Page 4 | |
Value used by ExactFitUnknown · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3632L Product sheet PDF Panel-ready top-view drawing: installed/niche depth at least 25 in.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 25 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | Unknown | ? Not found · Calculated/inferred | Miele KFMC3632L Product sheet PDF assets.skulytics.io | Page 4 | |
Value used by ExactFitUnknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25-in installed depth + standard 1-in handle projection Confidence label: medium. Primary evidenceMiele KFMC3632L Product sheet PDF Custom handles vary; recorded standardized 1-in projection.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 26 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | Unknown | ? Not found | Miele KFMC3632L Product sheet PDF assets.skulytics.io | Page 4 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3632L Product sheet PDF Manufacturer panel-ready 90-degree top-view dimension.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 57 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30 in | ✓ Secondary source only | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3836R Product sheet PDF Niche width in inches (mm), min. -> 30 (762)Open original source ↗ Why this value was usedNiche width in inches (mm), min. -> 30 (762) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84.125 in | ✓ Verified — equivalent model · Calculated/inferred | Miele KFMC3632L Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit84.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: reviewed MasterCool III family specification Confidence label: medium. Primary evidenceMiele KFMC3632L Product sheet PDF MasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set.Open original source ↗ Why this value was usedMasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set. Calculation or inference: reviewed MasterCool III family specification. Why evidence from KFMC3632L appliesTarget model: KFMC3836R. Supporting model: KFMC3632L. Manufacturer: Miele. Product family and measurement relationship: reviewed MasterCool III family specification. Measurement transferred: Minimum cutout height. Relevant equivalence evidence: MasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set.. Known differences: not separately recorded. Review decision: documented model family specification; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Secondary source only | Miele measurement source — https://www.designerappliances.com/miele-kfmc3836r.html www.designerappliances.com | Retained specification excerpt: Cutout Depth. 25 Inch | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceMiele measurement source — https://www.designerappliances.com/miele-kfmc3836r.html Cutout Depth. 25 InchOpen original source ↗ Why this value was usedCutout Depth. 25 Inch Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.0625 in | ✓ Secondary source only · Calculated/inferred | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele KFMC3836R Product sheet PDF Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.0625 in | ✓ Secondary source only · Calculated/inferred | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele KFMC3836R Product sheet PDF Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | Unknown | ? Not found · Calculated/inferred | Miele KFMC3632L Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 84.125 - 83.625 Confidence label: medium. Primary evidenceMiele KFMC3632L Product sheet PDF Top cavity delta: documented 84 1/8-in minimum niche height minus 83 5/8-in appliance height = 1/2 in.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Secondary source only · Calculated/inferred | Miele measurement source — https://www.designerappliances.com/miele-kfmc3836r.html www.designerappliances.com | Retained specification excerpt: Rear cavity clearance derived from verified niche depth 25 in minus case-only depth 24 in = 1 in. Ba | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: medium. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceMiele measurement source — https://www.designerappliances.com/miele-kfmc3836r.html Rear cavity clearance derived from verified niche depth 25 in minus case-only depth 24 in = 1 in. Base evidence: Cutout Depth. 25 InchOpen original source ↗ Why this value was usedRear cavity clearance derived from verified niche depth 25 in minus case-only depth 24 in = 1 in. Base evidence: Cutout Depth. 25 Inch Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | Unknown | ? Not found | Miele KFMC3632L Product sheet PDF assets.skulytics.io | Page 4 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3632L Product sheet PDF Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer panel-ready top view: 3/8-in side reveal/wall spacing.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.875 in | ✓ Secondary source only | Miele KFMC3836R Product sheet PDF assets.skulytics.io | Page 3 | |
Value used by ExactFit29.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3836R Product sheet PDF Appliance width in in.(mm) -> 29 7/8 (756)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 29 7/8 (756) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | Unknown | ? Not found | Miele KFMC3632L Product sheet PDF assets.skulytics.io | Page 4 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele KFMC3632L Product sheet PDF Manufacturer panel-ready top view: 3/8-in side reveal/wall spacing.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: Unknown. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: 105802871.pdf. Related-model record: KFMC3632L.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 105802871.pdf. Related-model record: KFMC3632L.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 105802871.pdf. Related-model record: KFMC3632L.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 105802871.pdf. Related-model record: KFMC3632L.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 105802871.pdf. Related-model record: KFMC3632L.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 105802871.pdf. Related-model record: KFMC3632L.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Product sheet PDF · secondary model/source
Model numbers covered: KFMC3836R. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product sheet PDF · Scope not established
Model numbers covered: KFMC3632L. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
7 displayed measurements supported: Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Top clearance; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.designerappliances.com · Web source · secondary model/source
Model numbers covered: KFMC3836R. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.