Measurement evidence for Miele KFMC3642R

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 105802897.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-04

Doors closed: 35 3/4" across the installed front (panel or stainless front). Measured across the installed door or panel (owner decision 2026-09-24).

Why this value was used

Doors closed: 35 3/4" across the installed front (panel or stainless front). Measured across the installed door or panel (owner decision 2026-09-24).

Other evidence found

• 35.25 in — superseded

  Document 105802897.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance width in in.(mm) -> 35 1/4 (894). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802897.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 5/8 (2123)

Why this value was used

Appliance height in in.(mm) -> 83 5/8 (2123)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802897.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 5/8 (2123)

Why this value was used

Appliance height in in.(mm) -> 83 5/8 (2123)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802897.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance depth in in.(mm) -> 24 (608)

Why this value was used

Appliance depth in in.(mm) -> 24 (608)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105803053.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Panel-ready top-view drawing: installed/niche depth at least 25 in.

Why this value was used

Panel-ready top-view drawing: installed/niche depth at least 25 in.

Other evidence found

• 24 in — superseded

  Document 105802897.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 (608). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

26 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25-in installed depth + standard 1-in handle projection

Confidence label: medium.

Primary evidence

Miele measurement source — 105803053.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Custom handles vary; recorded standardized 1-in projection.

Why this value was used

Custom handles vary; recorded standardized 1-in projection. Calculation or inference: 25-in installed depth + standard 1-in handle projection.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

63.9375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105803053.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Manufacturer panel-ready 90-degree top-view dimension.

Why this value was used

Manufacturer panel-ready 90-degree top-view dimension.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802897.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 36 (914)

Why this value was used

Niche width in inches (mm), min. -> 36 (914)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: reviewed MasterCool III family specification

Confidence label: medium.

Primary evidence

Miele specification record — 105803053.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

MasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set.

Why this value was used

MasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set. Calculation or inference: reviewed MasterCool III family specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: reviewed MasterCool III family specification

Confidence label: medium.

Primary evidence

Miele specification record — 105803053.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

MasterCool III technical data: niche depth 25 in; family/model list is shown in the installation drawing set.

Why this value was used

MasterCool III technical data: niche depth 25 in; family/model list is shown in the installation drawing set. Calculation or inference: reviewed MasterCool III family specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — KFMC3846L-105803053.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-04

Recalculated 2026-10-04 with the stored formula from current inputs: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 with case_width_in = 35.25, min_cutout_width_in = 36, width_doors_closed_in = 35.75 = 0.125 in (previously 0.375 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 with case_width_in = 35.25, min_cutout_width_in = 36, width_doors_closed_in = 35.75 = 0.125 in (previously 0.375 in). Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

• 0.375 in — superseded

  Document 105802897.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.25 in, divided by two = 0.375 in. Base evidence: Niche width in inches (mm), min. -> 36 (914). The final reviewed registry supersedes this earlier audit value.

• 0.375 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.375 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — KFMC3846L-105803053.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-04

Recalculated 2026-10-04 with the stored formula from current inputs: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 with case_width_in = 35.25, min_cutout_width_in = 36, width_doors_closed_in = 35.75 = 0.125 in (previously 0.375 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 with case_width_in = 35.25, min_cutout_width_in = 36, width_doors_closed_in = 35.75 = 0.125 in (previously 0.375 in). Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

• 0.375 in — superseded

  Document 105802897.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.25 in, divided by two = 0.375 in. Base evidence: Niche width in inches (mm), min. -> 36 (914). The final reviewed registry supersedes this earlier audit value.

• 0.375 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.375 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 84.125 - 83.625

Confidence label: medium.

Primary evidence

Miele measurement source — 105803053.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Top cavity delta: documented 84 1/8-in minimum niche height minus 83 5/8-in appliance height = 1/2 in.

Why this value was used

Top cavity delta: documented 84 1/8-in minimum niche height minus 83 5/8-in appliance height = 1/2 in. Calculation or inference: 84.125 - 83.625.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25 - 24

Confidence label: medium.

Primary evidence

Miele measurement source — 105803053.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Rear cavity delta: documented 25-in niche depth minus 24-in appliance case depth = 1 in.

Why this value was used

Rear cavity delta: documented 25-in niche depth minus 24-in appliance case depth = 1 in. Calculation or inference: 25 - 24.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.25 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802897.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 35 1/4 (894)

Why this value was used

Appliance width in in.(mm) -> 35 1/4 (894)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.