Measurement evidence for Miele KFMC3642L

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Miele KFMC3642L fit check Check this model against your opening How ExactFit verifies measurements

Miele KFMC3642L

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

0exact-model manufacturer values

2verified equivalent/same-chassis values

7secondary-source-only values

7values with unresolved source details

Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.25 in	✓ Secondary source only	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 35.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Appliance width in in.(mm) -> 35 1/4 (894) Open original source ↗ Why this value was used Appliance width in in.(mm) -> 35 1/4 (894) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	83.625 in	✓ Secondary source only	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 83.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Appliance height in in.(mm) -> 83 5/8 (2123) Open original source ↗ Why this value was used Appliance height in in.(mm) -> 83 5/8 (2123) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	83.625 in	✓ Secondary source only	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 83.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Appliance height in in.(mm) -> 83 5/8 (2123) Open original source ↗ Why this value was used Appliance height in in.(mm) -> 83 5/8 (2123) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24 in	✓ Secondary source only	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Appliance depth in in.(mm) -> 24 (608) Open original source ↗ Why this value was used Appliance depth in in.(mm) -> 24 (608) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	Unknown	? Not found	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 4
Value used by ExactFit Unknown · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Panel-ready top-view drawing: installed/niche depth at least 25 in. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 25 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 24 in — superseded 105802922.pdf (p.4); page 4. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 (608). The final reviewed registry supersedes this earlier audit value. Panel-ready top-view drawing: installed/niche depth at least 25 in. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	Unknown	? Not found · Calculated/inferred	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 4
Value used by ExactFit Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25-in installed depth + standard 1-in handle projection Confidence label: medium. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Custom handles vary; recorded standardized 1-in projection. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 26 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	Unknown	? Not found	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 4
Value used by ExactFit Unknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Manufacturer panel-ready 90-degree top-view dimension. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 63.9375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36 in	✓ Secondary source only	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Niche width in inches (mm), min. -> 36 (914) Open original source ↗ Why this value was used Niche width in inches (mm), min. -> 36 (914) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	84.125 in	✓ Verified — equivalent model · Calculated/inferred	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 2
Value used by ExactFit 84.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: reviewed MasterCool III family specification Confidence label: medium. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 MasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set. Open original source ↗ Why this value was used MasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set. Calculation or inference: reviewed MasterCool III family specification. Why evidence from KFMC3846L applies Target model: KFMC3642L. Supporting model: KFMC3846L. Manufacturer: Miele. Product family and measurement relationship: reviewed MasterCool III family specification. Measurement transferred: Minimum cutout height. Relevant equivalence evidence: MasterCool III technical data: niche height, minimum 84 1/8 in; family/model list is shown in the installation drawing set.. Known differences: not separately recorded. Review decision: documented model family specification; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	25 in	✓ Verified — equivalent model · Calculated/inferred	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 2
Value used by ExactFit 25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: reviewed MasterCool III family specification Confidence label: medium. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 MasterCool III technical data: niche depth 25 in; family/model list is shown in the installation drawing set. Open original source ↗ Why this value was used MasterCool III technical data: niche depth 25 in; family/model list is shown in the installation drawing set. Calculation or inference: reviewed MasterCool III family specification. Why evidence from KFMC3846L applies Target model: KFMC3642L. Supporting model: KFMC3846L. Manufacturer: Miele. Product family and measurement relationship: reviewed MasterCool III family specification. Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: MasterCool III technical data: niche depth 25 in; family/model list is shown in the installation drawing set.. Known differences: not separately recorded. Review decision: documented model family specification; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.375 in	✓ Secondary source only · Calculated/inferred	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.25 in, divided by two = 0.375 in. Base evidence: Niche width in inches (mm), min. -> 36 (914) Open original source ↗ Why this value was used Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.25 in, divided by two = 0.375 in. Base evidence: Niche width in inches (mm), min. -> 36 (914) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.375 in	✓ Secondary source only · Calculated/inferred	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.25 in, divided by two = 0.375 in. Base evidence: Niche width in inches (mm), min. -> 36 (914) Open original source ↗ Why this value was used Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.25 in, divided by two = 0.375 in. Base evidence: Niche width in inches (mm), min. -> 36 (914) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	Unknown	? Not found · Calculated/inferred	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 2
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 84.125 - 83.625 Confidence label: medium. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Top cavity delta: documented 84 1/8-in minimum niche height minus 83 5/8-in appliance height = 1/2 in. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	Unknown	? Not found · Calculated/inferred	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 2
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25 - 24 Confidence label: medium. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Rear cavity delta: documented 25-in niche depth minus 24-in appliance case depth = 1 in. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 1 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	Unknown	? Not found	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 4
Value used by ExactFit Unknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-05 Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer panel-ready top view: 3/8-in side reveal/wall spacing. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.25 in	✓ Secondary source only	Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io	Page 4
Value used by ExactFit 35.25 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3642L Operating and Installation instructions PDF assets.skulytics.io · Operating and Installation instructions PDF Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Appliance width in in.(mm) -> 35 1/4 (894) Open original source ↗ Why this value was used Appliance width in in.(mm) -> 35 1/4 (894) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	Unknown	? Not found	Miele KFMC3846L Product sheet PDF assets.skulytics.io	Page 4
Value used by ExactFit Unknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Miele KFMC3846L Product sheet PDF assets.skulytics.io · Product sheet PDF Model scope: Not established Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-09-04 Manufacturer panel-ready top view: 3/8-in side reveal/wall spacing. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Depth with door, without handles

Selected: Unknown. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.