Measurement evidence for Miele KFMC3632R

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802845.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 29 7/8 (756)

Why this value was used

Appliance width in in.(mm) -> 29 7/8 (756)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: right-hinge counterpart of exact KFMC3632L chassis

Confidence label: medium.

Primary evidence

Miele measurement source — 105802871.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Corrected to matching KFMC3632 left/right chassis height 83 5/8 in.

Why this value was used

Corrected to matching KFMC3632 left/right chassis height 83 5/8 in. Calculation or inference: right-hinge counterpart of exact KFMC3632L chassis.

Other evidence found

• 83.75 in — superseded

  Document 105802845.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Appliance height in in.(mm) -> 83 3/4 (2125). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: right-hinge counterpart of exact KFMC3632L chassis

Confidence label: medium.

Primary evidence

Miele measurement source — 105802871.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Corrected to matching KFMC3632 left/right chassis height 83 5/8 in.

Why this value was used

Corrected to matching KFMC3632 left/right chassis height 83 5/8 in. Calculation or inference: right-hinge counterpart of exact KFMC3632L chassis.

Other evidence found

• 83.75 in — superseded

  Document 105802845.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Appliance height in in.(mm) -> 83 3/4 (2125). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802845.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance depth in in.(mm) -> 24 (608)

Why this value was used

Appliance depth in in.(mm) -> 24 (608)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802871.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Panel-ready top-view drawing: installed/niche depth at least 25 in.

Why this value was used

Panel-ready top-view drawing: installed/niche depth at least 25 in.

Other evidence found

• 24 in — superseded

  Document 105802845.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 (608). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

26 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25-in installed depth + standard 1-in handle projection

Confidence label: medium.

Primary evidence

Miele measurement source — 105802871.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Custom handles vary; recorded standardized 1-in projection.

Why this value was used

Custom handles vary; recorded standardized 1-in projection. Calculation or inference: 25-in installed depth + standard 1-in handle projection.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

57 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802871.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Manufacturer panel-ready 90-degree top-view dimension.

Why this value was used

Manufacturer panel-ready 90-degree top-view dimension.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802845.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 30 (762)

Why this value was used

Niche width in inches (mm), min. -> 30 (762)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Miele measurement source — KFMC3632R.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cutout Height: 84 1/8 Inch
Reviewed: 2026-09-05

Cutout Height: 84 1/8 Inch

Why this value was used

Cutout Height: 84 1/8 Inch

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Miele measurement source — KFMC3632R.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cutout Depth: 25 Inch
Reviewed: 2026-09-05

Cutout Depth: 25 Inch

Why this value was used

Cutout Depth: 25 Inch

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — KFMC3632L-105802871.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — KFMC3632L-105802871.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in)

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Miele measurement source — KFMC3632R.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Top cavity clearance derived from verified niche height 84.125 in minus highest appliance height 83.
Reviewed: 2026-09-05

Top cavity clearance derived from verified niche height 84.125 in minus highest appliance height 83.625 in = 0.5 in. Base evidence: Cutout Height: 84 1/8 Inch

Why this value was used

Top cavity clearance derived from verified niche height 84.125 in minus highest appliance height 83.625 in = 0.5 in. Base evidence: Cutout Height: 84 1/8 Inch Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: medium.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Miele measurement source — KFMC3632R.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Rear cavity clearance derived from verified niche depth 25 in minus case-only depth 24 in = 1 in. Ba
Reviewed: 2026-09-05

Rear cavity clearance derived from verified niche depth 25 in minus case-only depth 24 in = 1 in. Base evidence: Cutout Depth: 25 Inch

Why this value was used

Rear cavity clearance derived from verified niche depth 25 in minus case-only depth 24 in = 1 in. Base evidence: Cutout Depth: 25 Inch Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Miele measurement source — 105802871.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer panel-ready top view: 3/8-in side reveal/wall spacing.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Manufacturer panel-ready top view: 3/8-in side reveal/wall spacing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105802845.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 29 7/8 (756)

Why this value was used

Appliance width in in.(mm) -> 29 7/8 (756)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.