Measurement evidence for Miele KF2902SF

Value used by ExactFit

36.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524085.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-03

Door closed: 36.5 in across the installed door; the case width is narrower. Measured across the installed door or panel (owner decision 2026-09-24, as for K2802SFSS).

Why this value was used

Door closed: 36.5 in across the installed door; the case width is narrower. Measured across the installed door or panel (owner decision 2026-09-24, as for K2802SFSS).

Other evidence found

• 35.75 in — superseded

  Document 74524085.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Appliance width in in.(mm) -> 35 3/4 (908). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524085.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524085.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524085.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance depth in in.(mm) -> 24 (608)

Why this value was used

Appliance depth in in.(mm) -> 24 (608)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524085.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-03

Door closed, no projecting handle: at least 24 3/4 in (629 mm) across the installed door; the appliance alone is 24 in. Depth across the installed door (owner decision 2026-09-24).

Why this value was used

Door closed, no projecting handle: at least 24 3/4 in (629 mm) across the installed door; the appliance alone is 24 in. Depth across the installed door (owner decision 2026-09-24).

Other evidence found

• 24 in — superseded

  Document 74524085.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 (608). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + standard 1-in handle projection

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Manufacturer drawing identifies front/handle contributions; standardized handle scenario.

Why this value was used

Manufacturer drawing identifies front/handle contributions; standardized handle scenario. Calculation or inference: depth_less_handles_in + standard 1-in handle projection.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

62.6875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in case depth + manufacturer 90-degree door projection A

Confidence label: high.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

MasterCool 36-in chassis 90-degree plan dimension.

Why this value was used

MasterCool 36-in chassis 90-degree plan dimension. Calculation or inference: 24-in case depth + manufacturer 90-degree door projection A.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524085.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 36 (914)

Why this value was used

Niche width in inches (mm), min. -> 36 (914)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524085.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.

Why this value was used

Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524085.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.125 in; supersedes prior metric-normalized/family value 24.0.

Why this value was used

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.125 in; supersedes prior metric-normalized/family value 24.0.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — KF2902SF-74524085.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.125 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.125 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — KF2902SF-74524085.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.125 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.125 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in)

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Miele measurement source — KF2902SF-74524085.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.375 in exactly. This is an installation reveal, normalized to the database top_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.375 in exactly. This is an installation reveal, normalized to the database top_clearance_in term. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: high.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Miele measurement source — KF2902SF-74524085.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.125 in exactly. This is an installation reveal, normalized to the database rear_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.125 in exactly. This is an installation reveal, normalized to the database rear_clearance_in term. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524088.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-03

Top view, doorway (KF2902SF, KF2912SF, KF2901SF, KF2911SF): 4" (102 mm) from the niche side to the outer face of the door open at 90 degrees, with the furniture front installed. The 3/8" (10 mm) in the generic K 26x2-29x2 SF manual (p.23) is the bare door without a furniture front; panel-ready doors are measured with the installed panel (owner decision 2026-09-24).

Why this value was used

Top view, doorway (KF2902SF, KF2912SF, KF2901SF, KF2911SF): 4" (102 mm) from the niche side to the outer face of the door open at 90 degrees, with the furniture front installed. The 3/8" (10 mm) in the generic K 26x2-29x2 SF manual (p.23) is the bare door without a furniture front; panel-ready doors are measured with the installed panel (owner decision 2026-09-24).

Other evidence found

• 0.375 in — superseded

  Document 105807404.pdf; page 23. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524085.pdf (p.3)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 35 3/4 (908)

Why this value was used

Appliance width in in.(mm) -> 35 3/4 (908)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.