Measurement evidence for Miele K31222UI

Value used by ExactFit

23.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524040.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 23 5/8 (597)

Why this value was used

Appliance width in in.(mm) -> 23 5/8 (597)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.3125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524041.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 49
Reviewed: 2026-09-18

Installation dimensions drawing (page 49) prints the appliance height 32 5/16" - 34 5/8" (adjustable); the product sheet prints 32 3/8 (820), but 820 mm is 32 5/16 in. The minimum setting is recorded.

Why this value was used

Installation dimensions drawing (page 49) prints the appliance height 32 5/16" - 34 5/8" (adjustable); the product sheet prints 32 3/8 (820), but 820 mm is 32 5/16 in. The minimum setting is recorded.

Other evidence found

• 32.375 in — superseded

  Document 74524040.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance height in in.(mm) -> 32 3/8 (820). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.3125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524041.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 49
Reviewed: 2026-09-18

Installation dimensions drawing (page 49) prints the appliance height 32 5/16" - 34 5/8" (adjustable); the product sheet prints 32 3/8 (820), but 820 mm is 32 5/16 in. The minimum setting is recorded.

Why this value was used

Installation dimensions drawing (page 49) prints the appliance height 32 5/16" - 34 5/8" (adjustable); the product sheet prints 32 3/8 (820), but 820 mm is 32 5/16 in. The minimum setting is recorded.

Other evidence found

• 32.375 in — superseded

  Document 74524040.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance height in in.(mm) -> 32 3/8 (820). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

21.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — K31222Ui-74524041.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 49
Reviewed: 2026-09-11

Exact-model Miele installation drawing prints appliance depth 21 11/16 in.

Why this value was used

Exact-model Miele installation drawing prints appliance depth 21 11/16 in.

Other evidence found

• 21.75 in — superseded

  Document 74524040.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 21 3/4 (550). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.5 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 21.75-in niche + 0.75-in panel

Confidence label: medium.

Primary evidence

Miele measurement source — 74524040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Standard panel configuration.

Why this value was used

Standard panel configuration. Calculation or inference: 21.75-in niche + 0.75-in panel.

Other evidence found

• 21.75 in — superseded

  Document 74524040.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 21 3/4 (550). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

23.5 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 1-in handle

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Miele measurement source — 74524040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Custom handles vary.

Why this value was used

Custom handles vary. Calculation or inference: depth_less_handles_in + 1-in handle.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.4 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Miele installation document — 74524040.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Published device/open-door depth: 48.4 in.

Why this value was used

Published device/open-door depth: 48.4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

23.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524040.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 23 5/8 (600)

Why this value was used

Niche width in inches (mm), min. -> 23 5/8 (600)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.3125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — K31222Ui-74524041.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 50
Reviewed: 2026-09-11

Exact-model Miele installation drawing prints niche height range 32 5/16 to 34 5/8 in; database stores the minimum.

Why this value was used

Exact-model Miele installation drawing prints niche height range 32 5/16 to 34 5/8 in; database stores the minimum.

Other evidence found

• 32.25 in — superseded

  Document 74524040.pdf; page 1. Model scope: not separately recorded. Raw value: Exact-model Miele product sheet: minimum niche height 820 mm; normalized to nearest 1/8 in = 32.25 in.. The final reviewed registry supersedes this earlier audit value.

• 32.375 in — superseded

  Document 74524040.pdf; page 1. Model scope: not separately recorded. Raw value: Exact-model US Miele product sheet explicitly states min_cutout_height_in=32.375 in; supersedes prior metric-normalized/family value 32.25.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

21.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524041.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 50
Reviewed: 2026-09-18

Dimensions for ventilation (page 50): "The appliance is fully capable of functioning at a niche depth of 21 5/8" (550 mm), but will consume slightly more energy"; declared energy use needs 22 1/16" (560 mm). The drawing's "min. 21 1/4" line is taken as the lower cabinet-side depth, not the niche. Owner decision 2026-09-18.

Why this value was used

Dimensions for ventilation (page 50): "The appliance is fully capable of functioning at a niche depth of 21 5/8" (550 mm), but will consume slightly more energy"; declared energy use needs 22 1/16" (560 mm). The drawing's "min. 21 1/4" line is taken as the lower cabinet-side depth, not the niche. Owner decision 2026-09-18.

Other evidence found

• 21.75 in — superseded

  Document 74524040.pdf; page 1. Model scope: not separately recorded. Raw value: Exact-model US Miele product sheet explicitly states min_cutout_depth_in=21.75 in; supersedes prior metric-normalized/family value 21.625.. The final reviewed registry supersedes this earlier audit value.

• 21.25 in — superseded

  assets.skulytics.io; page 50. Model scope: not separately recorded. Raw value: Exact-model Miele installation drawing labels minimum niche depth 21 1/4 in; 21 5/8 in is the deeper energy-rating scenario.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — K31222Ui-74524040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — K31222Ui-74524040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in)

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Miele measurement source — K31222Ui-74524040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database top_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0 in exactly. This is an installation reveal, normalized to the database top_clearance_in term. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Miele measurement source — 74524041.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 50
Reviewed: 2026-09-18

Built-in niche with no rear gap: the minimum niche depth 21 5/8" (550 mm) and the 21 11/16" appliance body are the same to within Miele's rounding. Replaces the formula "min_cutout_depth_in - depth_case_only_in", which gave -1/16 in. Owner decision 2026-09-18.

Why this value was used

Built-in niche with no rear gap: the minimum niche depth 21 5/8" (550 mm) and the 21 11/16" appliance body are the same to within Miele's rounding. Replaces the formula "min_cutout_depth_in - depth_case_only_in", which gave -1/16 in. Owner decision 2026-09-18. Calculation or inference: agent blind extraction visually confirmed.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented 3-mm minimum rounded to 1/8 in

Confidence label: medium.

Primary evidence

Miele measurement source — 74524040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Minimum furniture/wall gap.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Minimum furniture/wall gap. Calculation or inference: documented 3-mm minimum rounded to 1/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

23.5 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — K31222Ui-74524041.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 49
Reviewed: 2026-09-11

Exact-model Miele installation drawing prints appliance width 23 1/2 in.

Why this value was used

Exact-model Miele installation drawing prints appliance width 23 1/2 in.

Other evidence found

• 23.625 in — superseded

  Document 74524040.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance width in in.(mm) -> 23 5/8 (597). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.