This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Appliance width in in.(mm) -> 35 3/4 (908)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 35 3/4 (908) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.75 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Appliance height in in.(mm) -> 83 3/4 (2125)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 83 3/4 (2125) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.75 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Appliance height in in.(mm) -> 83 3/4 (2125)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 83 3/4 (2125) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Appliance depth in in.(mm) -> 24 (608)Open original source ↗ Why this value was usedAppliance depth in in.(mm) -> 24 (608) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Appliance depth in in.(mm) -> 24 (608)Open original source ↗ Why this value was usedAppliance depth in in.(mm) -> 24 (608) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 25 in | ✓ Secondary source only · Calculated/inferred | Miele K2602SFSS Operating and Installation instructions PDF assets.skulytics.io | Page 23 | |
Value used by ExactFit25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + standard 1-in handle projection Confidence label: medium. Calculation inputs: Depth with door, without handles; Primary evidenceMiele K2602SFSS Operating and Installation instructions PDF Manufacturer drawing identifies front/handle contributions; standardized handle scenario.Open original source ↗ Why this value was usedManufacturer drawing identifies front/handle contributions; standardized handle scenario. Calculation or inference: depth_less_handles_in + standard 1-in handle projection. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 62.6875 in | ✓ Verified — equivalent model · Calculated/inferred | Miele K2602SFSS Operating and Installation instructions PDF assets.skulytics.io | Page 23 | |
Value used by ExactFit62.6875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24-in case depth + manufacturer 90-degree door projection A Confidence label: high. Primary evidenceMiele K2602SFSS Operating and Installation instructions PDF MasterCool 36-in chassis 90-degree plan dimension.Open original source ↗ Why this value was usedMasterCool 36-in chassis 90-degree plan dimension. Calculation or inference: 24-in case depth + manufacturer 90-degree door projection A. Why evidence from K2602SFSS appliesTarget model: K2902SFSS. Supporting model: K2602SFSS. Manufacturer: Miele. Product family and measurement relationship: 24-in case depth + manufacturer 90-degree door projection A. Measurement transferred: Depth with doors open at 90°. Relevant equivalence evidence: MasterCool 36-in chassis 90-degree plan dimension.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Niche width in inches (mm), min. -> 36 (914)Open original source ↗ Why this value was usedNiche width in inches (mm), min. -> 36 (914) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84.125 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit84.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.Open original source ↗ Why this value was usedExact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24.125 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit24.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.125 in; supersedes prior metric-normalized/family value 24.0.Open original source ↗ Why this value was usedExact-model US Miele product sheet explicitly states min_cutout_depth_in=24.125 in; supersedes prior metric-normalized/family value 24.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele K2902SFSS Product sheet PDF Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.75 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 (914)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.75 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 (914) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele K2902SFSS Product sheet PDF Per-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.75 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 (914)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 36 in minus widest closed appliance width 35.75 in, divided by two = 0.125 in. Base evidence: Niche width in inches (mm), min. -> 36 (914) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.375 in | ✓ Conflicting sources — resolved · Calculated/inferred | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in) Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height; Primary evidenceMiele K2902SFSS Product sheet PDF Recomputed from exact-model US product sheet: 84.125 in niche dimension minus 83.75 in verified appliance dimension = 0.375 in; supersedes prior value 0.25.Open original source ↗ Why this value was usedRecomputed from exact-model US product sheet: 84.125 in niche dimension minus 83.75 in verified appliance dimension = 0.375 in; supersedes prior value 0.25. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in). Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: medium. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceMiele K2902SFSS Product sheet PDF Recomputed from exact-model US product sheet: 24.125 in niche dimension minus 24 in verified appliance dimension = 0.125 in; supersedes prior value 0.0.Open original source ↗ Why this value was usedRecomputed from exact-model US product sheet: 24.125 in niche dimension minus 24 in verified appliance dimension = 0.125 in; supersedes prior value 0.0. Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | Unknown | ? Not found | Miele K2602SFSS Operating and Installation instructions PDF assets.skulytics.io | Page 23 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2602SFSS Operating and Installation instructions PDF Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Secondary source only | Miele K2902SFSS Product sheet PDF assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2902SFSS Product sheet PDF Appliance width in in.(mm) -> 35 3/4 (908)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 35 3/4 (908) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | Unknown | ? Not found | Miele K2602SFSS Operating and Installation instructions PDF assets.skulytics.io | Page 23 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele K2602SFSS Operating and Installation instructions PDF Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 0.375 in. Earlier retained values: 0.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Recomputed from exact-model US product sheet: 84.125 in niche dimension minus 83.75 in verified appliance dimension = 0.375 in; supersedes prior value 0.25. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: 105807404.pdf. Related-model record: K2602SFSS.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: 105807404.pdf. Related-model record: K2602SFSS.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Product sheet PDF · secondary model/source
Model numbers covered: K2902SFSS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Operating and Installation instructions PDF · Scope not established
Model numbers covered: K2602SFSS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Depth with handle; Depth with doors open at 90°; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product sheet PDF · secondary model/source
Model numbers covered: K2902SFSS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.