Measurement evidence for Miele K2812VI

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524033.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 29 7/8 (756)

Why this value was used

Appliance width in in.(mm) -> 29 7/8 (756)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524033.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524033.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524033.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance depth in in.(mm) -> 24 (608)

Why this value was used

Appliance depth in in.(mm) -> 24 (608)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in case + supplied front (SF/CTS) or standard 3/4-in custom panel

Confidence label: medium.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Installed-depth normalization; panel-ready value uses a standard 3/4-in panel.

Why this value was used

Installed-depth normalization; panel-ready value uses a standard 3/4-in panel. Calculation or inference: 24-in case + supplied front (SF/CTS) or standard 3/4-in custom panel.

Other evidence found

• 24 in — superseded

  Document 74524033.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 (608). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + standard 1-in handle projection

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Manufacturer drawing identifies front/handle contributions; standardized handle scenario.

Why this value was used

Manufacturer drawing identifies front/handle contributions; standardized handle scenario. Calculation or inference: depth_less_handles_in + standard 1-in handle projection.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

56.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in case depth + manufacturer 90-degree door projection A

Confidence label: high.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

MasterCool 30-in chassis 90-degree plan dimension.

Why this value was used

MasterCool 30-in chassis 90-degree plan dimension. Calculation or inference: 24-in case depth + manufacturer 90-degree door projection A.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524033.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 30 (762)

Why this value was used

Niche width in inches (mm), min. -> 30 (762)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524033.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.

Why this value was used

Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 74524033.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.875 in; supersedes prior metric-normalized/family value 24.75.

Why this value was used

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.875 in; supersedes prior metric-normalized/family value 24.75.

Other evidence found

• 24.75 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Exact-model Miele product sheet: niche depth 629 mm; normalized to nearest 1/8 in = 24.75 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — K2812Vi-74524033.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: high.

Calculation inputs: Overall width; Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — K2812Vi-74524033.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term. Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in)

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Miele measurement source — K2812Vi-74524033.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.375 in exactly. This is an installation reveal, normalized to the database top_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.375 in exactly. This is an installation reveal, normalized to the database top_clearance_in term. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).

Other evidence found

• 0.25 in — superseded

  Document c83bfa2ac74e69cf1e792dd731482b8862ef6e78d2fffa0b12ec7846e0f388ec.pdf; page 34. Model scope: not separately recorded. Raw value: Top cavity clearance derived from verified niche height 84 in minus highest appliance height 83.75 in = 0.25 in. Base evidence: niche height of 84”. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: high.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Miele measurement source — K2812Vi-74524033.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.875 in exactly. This is an installation reveal, normalized to the database rear_clearance_in term.

Why this value was used

Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.875 in exactly. This is an installation reveal, normalized to the database rear_clearance_in term. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

• 0.75 in — superseded

  Document 74524033.pdf; page 1. Model scope: not separately recorded. Raw value: Rear cavity delta from exact-model sheet: normalized niche depth 24.75 in minus verified case-only depth 24 in = 0.75 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 74524033.pdf (p.1)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 29 7/8 (756)

Why this value was used

Appliance width in in.(mm) -> 29 7/8 (756)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.