Measurement evidence for Miele K2802SFSS

Value used by ExactFit

30.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 105808021.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-24

Door closed: width across the installed door 30 1/2 in (775 mm); the appliance (case) width is 29 3/4 in (756 mm). The stored value was the case width.

Why this value was used

Door closed: width across the installed door 30 1/2 in (775 mm); the appliance (case) width is 29 3/4 in (756 mm). The stored value was the case width.

Other evidence found

• 29.875 in — superseded

  Document 105808021.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: Appliance width in in.(mm) -> 29 7/8 (756). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105808021.pdf (p.2)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105808021.pdf (p.2)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105808021.pdf (p.2)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Appliance depth in in.(mm) -> 24 (608)

Why this value was used

Appliance depth in in.(mm) -> 24 (608)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 105808021.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-24

Door closed, no projecting handle: at least 24 3/4 in (629 mm) across the installed door; the appliance depth alone is 24 in (608 mm).

Why this value was used

Door closed, no projecting handle: at least 24 3/4 in (629 mm) across the installed door; the appliance depth alone is 24 in (608 mm).

Other evidence found

• 24 in — superseded

  Document 105808021.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 (608). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + standard 1-in handle projection

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Manufacturer drawing identifies front/handle contributions; standardized handle scenario.

Why this value was used

Manufacturer drawing identifies front/handle contributions; standardized handle scenario. Calculation or inference: depth_less_handles_in + standard 1-in handle projection.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

56.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in case depth + manufacturer 90-degree door projection A

Confidence label: high.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

MasterCool 30-in chassis 90-degree plan dimension.

Why this value was used

MasterCool 30-in chassis 90-degree plan dimension. Calculation or inference: 24-in case depth + manufacturer 90-degree door projection A.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele installation document — 105808021.pdf (p.2)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 30 (762)

Why this value was used

Niche width in inches (mm), min. -> 30 (762)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 21
Reviewed: 2026-09-17

Installation dimensions table: A niche height 84"-85 3/16" (2,134-2,164 mm) and C niche depth 24" (610 mm) for K 2602/K 2612, K 2802/K 2812 and K 2902/K 2912; B niche width 24" (610 mm) for K 2602 SF. The product sheets print 24 1/8 (610) and 84 1/8 (2134), but 610 mm is 24 in and 2134 mm is 84 in.

Why this value was used

Installation dimensions table: A niche height 84"-85 3/16" (2,134-2,164 mm) and C niche depth 24" (610 mm) for K 2602/K 2612, K 2802/K 2812 and K 2902/K 2912; B niche width 24" (610 mm) for K 2602 SF. The product sheets print 24 1/8 (610) and 84 1/8 (2134), but 610 mm is 24 in and 2134 mm is 84 in.

Other evidence found

• 84.125 in — superseded

  Document 105808021.pdf; page 2. Model scope: not separately recorded. Raw value: Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 21
Reviewed: 2026-09-17

Installation dimensions table: A niche height 84"-85 3/16" (2,134-2,164 mm) and C niche depth 24" (610 mm) for K 2602/K 2612, K 2802/K 2812 and K 2902/K 2912; B niche width 24" (610 mm) for K 2602 SF. The product sheets print 24 1/8 (610) and 84 1/8 (2134), but 610 mm is 24 in and 2134 mm is 84 in.

Why this value was used

Installation dimensions table: A niche height 84"-85 3/16" (2,134-2,164 mm) and C niche depth 24" (610 mm) for K 2602/K 2612, K 2802/K 2812 and K 2902/K 2912; B niche width 24" (610 mm) for K 2602 SF. The product sheets print 24 1/8 (610) and 84 1/8 (2134), but 610 mm is 24 in and 2134 mm is 84 in.

Other evidence found

• 24.125 in — superseded

  Document 105808021.pdf; page 2. Model scope: not separately recorded. Raw value: Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.125 in; supersedes prior metric-normalized/family value 24.0.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: side_ventilation_clearance_in = (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — 105808021.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-24

Niche width 30 in (762 mm) less the 29 3/4 in (756 mm) appliance width, halved: 1/8 in per side. The door overlaps the cabinet face and is not counted, so the closed-door width is not used here.

Why this value was used

Niche width 30 in (762 mm) less the 29 3/4 in (756 mm) appliance width, halved: 1/8 in per side. The door overlaps the cabinet face and is not counted, so the closed-door width is not used here. Calculation or inference: side_ventilation_clearance_in = (min_cutout_width_in - case_width_in) / 2.

Other evidence found

• 0.0625 in — superseded

  Document 105808021.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762). The final reviewed registry supersedes this earlier audit value.

• 0.0625 in — superseded

  assets.skulytics.io; page 2. Model scope: not separately recorded. Raw value: Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: side_ventilation_clearance_in = (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Minimum cutout width; Cabinet case width;

Primary evidence

Miele measurement source — 105808021.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-24

Niche width 30 in (762 mm) less the 29 3/4 in (756 mm) appliance width, halved: 1/8 in per side. The door overlaps the cabinet face and is not counted, so the closed-door width is not used here.

Why this value was used

Niche width 30 in (762 mm) less the 29 3/4 in (756 mm) appliance width, halved: 1/8 in per side. The door overlaps the cabinet face and is not counted, so the closed-door width is not used here. Calculation or inference: side_ventilation_clearance_in = (min_cutout_width_in - case_width_in) / 2.

Other evidence found

• 0.0625 in — superseded

  Document 105808021.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: Per-side cavity reveal derived from verified niche width 30 in minus widest closed appliance width 29.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 30 (762). The final reviewed registry supersedes this earlier audit value.

• 0.0625 in — superseded

  assets.skulytics.io; page 2. Model scope: not separately recorded. Raw value: Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.0625 in exactly. This is an installation reveal, normalized to the database side_ventilation_clearance_in term.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in)

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 21
Reviewed: 2026-09-17

Recalculated with the stored formula after the niche height was corrected from 84 1/8 to 84 in, which is what the millimetres printed on every Miele document give. 84 - 83 3/4 = 1/4 in.

Why this value was used

Recalculated with the stored formula after the niche height was corrected from 84 1/8 to 84 in, which is what the millimetres printed on every Miele document give. 84 - 83 3/4 = 1/4 in. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).

Other evidence found

• 0.375 in — superseded

  Document 105808021.pdf; page 2. Model scope: not separately recorded. Raw value: Recomputed from exact-model US product sheet: 84.125 in niche dimension minus 83.75 in verified appliance dimension = 0.375 in; supersedes prior value 0.25.. The final reviewed registry supersedes this earlier audit value.

• 0.375 in — superseded

  assets.skulytics.io; page 2. Model scope: not separately recorded. Raw value: Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.375 in exactly. This is an installation reveal, normalized to the database top_clearance_in term.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: high.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 21
Reviewed: 2026-09-17

Recalculated with the stored formula after the niche depth was corrected from 24 1/8 to 24 in, which is what the millimetres printed on every Miele document give. 24 - 24 = 0 in.

Why this value was used

Recalculated with the stored formula after the niche depth was corrected from 24 1/8 to 24 in, which is what the millimetres printed on every Miele document give. 24 - 24 = 0 in. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

• 0.125 in — superseded

  Document 105808021.pdf; page 2. Model scope: not separately recorded. Raw value: Recomputed from exact-model US product sheet: 24.125 in niche dimension minus 24 in verified appliance dimension = 0.125 in; supersedes prior value 0.0.. The final reviewed registry supersedes this earlier audit value.

• 0.125 in — superseded

  assets.skulytics.io; page 2. Model scope: not separately recorded. Raw value: Exact-model Miele technical-data page was visually checked. The printed niche and appliance dimensions are high-confidence operands; applying the Miele built-in cavity-residual rule reproduces 0.125 in exactly. This is an installation reveal, normalized to the database rear_clearance_in term.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Miele measurement source — 105807404.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele measurement source — 105808021.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-24

Appliance width 756 mm. The sheet's own inch column prints 29 7/8, which is 758.8 mm and disagrees with its metric value; 756 mm is 29 3/4 in, and the installation drawing on page 3 prints 29 3/4.

Why this value was used

Appliance width 756 mm. The sheet's own inch column prints 29 7/8, which is 758.8 mm and disagrees with its metric value; 756 mm is 29 3/4 in, and the installation drawing on page 3 prints 29 3/4.

Other evidence found

• 29.875 in — superseded

  Document 105808021.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: Appliance width in in.(mm) -> 29 7/8 (756). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.