This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 22.125 in | ✓ Secondary source only | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit22.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Appliance width in in.(mm) -> 22 1/8 (559)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 22 1/8 (559) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69.75 in | ✓ Secondary source only | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Appliance height in in.(mm) -> 69 3/4 (1770)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 69 3/4 (1770) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.75 in | ✓ Secondary source only | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Appliance height in in.(mm) -> 69 3/4 (1770)Open original source ↗ Why this value was usedAppliance height in in.(mm) -> 69 3/4 (1770) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 21.5 in | ✓ Secondary source only | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit21.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Appliance depth in in.(mm) -> 21 1/2 (544)Open original source ↗ Why this value was usedAppliance depth in in.(mm) -> 21 1/2 (544) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 22.25 in | ✓ Conflicting sources — resolved · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit22.25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 21.5-in case + standard 3/4-in furniture panel Confidence label: medium. Primary evidenceMiele FNS37492IE Product sheet Standardized installed configuration.Open original source ↗ Why this value was usedStandardized installed configuration. Calculation or inference: 21.5-in case + standard 3/4-in furniture panel. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 23.25 in | ✓ Secondary source only · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit23.25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + standard 1-in handle Confidence label: medium. Calculation inputs: Depth with door, without handles; Primary evidenceMiele FNS37492IE Product sheet Custom handles vary.Open original source ↗ Why this value was usedCustom handles vary. Calculation or inference: depth_less_handles_in + standard 1-in handle. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | Unknown | ? Not found · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 3 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 21.5-in case + 22.125-in door width + 0.75-in panel Confidence label: medium. Primary evidenceMiele FNS37492IE Product sheet 90-degree geometric extent for documented chassis and standard panel.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 44.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 22.125 in | ✓ Secondary source only | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit22.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Niche width in inches (mm), min. -> 22 1/8 (560)Open original source ↗ Why this value was usedNiche width in inches (mm), min. -> 22 1/8 (560) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.875 in | ✓ Conflicting sources — resolved | Miele FNS37492IE Product sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Exact-model US Miele product sheet explicitly states min_cutout_height_in=69.875 in; supersedes prior metric-normalized/family value 69.75.Open original source ↗ Why this value was usedExact-model US Miele product sheet explicitly states min_cutout_height_in=69.875 in; supersedes prior metric-normalized/family value 69.75. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 21.75 in | ✓ Secondary source only | Miele FNS37492IE Product sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit21.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Exact-model US Miele product sheet explicitly states min_cutout_depth_in=21.75 in; supersedes prior metric-normalized/family value 21.625.Open original source ↗ Why this value was usedExact-model US Miele product sheet explicitly states min_cutout_depth_in=21.75 in; supersedes prior metric-normalized/family value 21.625. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0 in | ✓ Secondary source only · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele FNS37492IE Product sheet Per-side cavity reveal derived from verified niche width 22.125 in minus widest closed appliance width 22.125 in, divided by two = 0 in. Base evidence: Niche width in inches (mm), min. -> 22 1/8 (560)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 22.125 in minus widest closed appliance width 22.125 in, divided by two = 0 in. Base evidence: Niche width in inches (mm), min. -> 22 1/8 (560) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0 in | ✓ Secondary source only · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2 Confidence label: medium. Calculation inputs: Cabinet case width; Overall width; Minimum cutout width; Primary evidenceMiele FNS37492IE Product sheet Per-side cavity reveal derived from verified niche width 22.125 in minus widest closed appliance width 22.125 in, divided by two = 0 in. Base evidence: Niche width in inches (mm), min. -> 22 1/8 (560)Open original source ↗ Why this value was usedPer-side cavity reveal derived from verified niche width 22.125 in minus widest closed appliance width 22.125 in, divided by two = 0 in. Base evidence: Niche width in inches (mm), min. -> 22 1/8 (560) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.125 in | ✓ Conflicting sources — resolved · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in) Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height; Primary evidenceMiele FNS37492IE Product sheet Recomputed from exact-model US product sheet: 69.875 in niche dimension minus 69.75 in verified appliance dimension = 0.125 in; supersedes prior value 0.0.Open original source ↗ Why this value was usedRecomputed from exact-model US product sheet: 69.875 in niche dimension minus 69.75 in verified appliance dimension = 0.125 in; supersedes prior value 0.0. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in). Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.25 in | ✓ Conflicting sources — resolved · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: medium. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceMiele FNS37492IE Product sheet Recomputed from exact-model US product sheet: 21.75 in niche dimension minus 21.5 in verified appliance dimension = 0.25 in; supersedes prior value 0.125.Open original source ↗ Why this value was usedRecomputed from exact-model US product sheet: 21.75 in niche dimension minus 21.5 in verified appliance dimension = 0.25 in; supersedes prior value 0.125. Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit0.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented 3-mm minimum rounded to 1/8 in Confidence label: medium. Primary evidenceMiele FNS37492IE Product sheet Verified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Minimum adjoining-panel/wall gap for standard furniture front.Open original source ↗ Why this value was usedVerified legacy adjoining-wall/hinge clearance migrated to the explicit hinge-side wall field. Minimum adjoining-panel/wall gap for standard furniture front. Calculation or inference: documented 3-mm minimum rounded to 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 22.125 in | ✓ Secondary source only | Miele FNS37492IE Product sheet assets.skulytics.io | Page 2 | |
Value used by ExactFit22.125 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMiele FNS37492IE Product sheet Appliance width in in.(mm) -> 22 1/8 (559)Open original source ↗ Why this value was usedAppliance width in in.(mm) -> 22 1/8 (559) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 0.125 in | ✓ Secondary source only · Calculated/inferred | Miele FNS37492IE Product sheet assets.skulytics.io | Page 3 | |
Value used by ExactFit0.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented 3-mm minimum rounded to 1/8 in Confidence label: medium. Primary evidenceMiele FNS37492IE Product sheet Minimum adjoining-panel/wall gap for standard furniture front.Open original source ↗ Why this value was usedMinimum adjoining-panel/wall gap for standard furniture front. Calculation or inference: documented 3-mm minimum rounded to 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 22.25 in. Earlier retained values: 21.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Standardized installed configuration. Calculation or inference: 21.5-in case + standard 3/4-in furniture panel.
View source scope, location, and impact on fitSelected: 69.875 in. Earlier retained values: 69.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model US Miele product sheet explicitly states min_cutout_height_in=69.875 in; supersedes prior metric-normalized/family value 69.75.
View source scope, location, and impact on fitSelected: 0.125 in. Earlier retained values: 0 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Recomputed from exact-model US product sheet: 69.875 in niche dimension minus 69.75 in verified appliance dimension = 0.125 in; supersedes prior value 0.0. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).
View source scope, location, and impact on fitSelected: 0.25 in. Earlier retained values: 0.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Recomputed from exact-model US product sheet: 21.75 in niche dimension minus 21.5 in verified appliance dimension = 0.25 in; supersedes prior value 0.125. Calculation or inference: min_cutout_depth_in - depth_case_only_in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: 74524100.pdf. Related-model record: FNS37492IE.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Product sheet · secondary model/source
Model numbers covered: FNS37492IE. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product sheet · secondary model/source
Model numbers covered: FNS37492IE. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.