Measurement evidence for Miele F2472VI

Value used by ExactFit

17.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 17 7/8 (451)

Why this value was used

Appliance width in in.(mm) -> 17 7/8 (451)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance height in in.(mm) -> 83 3/4 (2125)

Why this value was used

Appliance height in in.(mm) -> 83 3/4 (2125)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance depth in in.(mm) -> 24 (608)

Why this value was used

Appliance depth in in.(mm) -> 24 (608)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in case + supplied front (SF/CTS) or standard 3/4-in custom panel

Confidence label: medium.

Primary evidence

Miele F2412SFSS Operating and Installation instructions PDF
assets.skulytics.io · Operating and Installation instructions PDF
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Installed-depth normalization; panel-ready value uses a standard 3/4-in panel.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 24.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

• 24 in — superseded

  74524104.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Appliance depth in in.(mm) -> 24 (608). The final reviewed registry supersedes this earlier audit value. Installed-depth normalization; panel-ready value uses a standard 3/4-in panel.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + standard 1-in handle projection

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Miele F2412SFSS Operating and Installation instructions PDF
assets.skulytics.io · Operating and Installation instructions PDF
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Manufacturer drawing identifies front/handle contributions; standardized handle scenario.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 25.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44.6875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in case depth + manufacturer 90-degree door projection A

Confidence label: high.

Primary evidence

Miele F2412SFSS Operating and Installation instructions PDF
assets.skulytics.io · Operating and Installation instructions PDF
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

MasterCool 18-in chassis 90-degree plan dimension.

Why this value was used

MasterCool 18-in chassis 90-degree plan dimension. Calculation or inference: 24-in case depth + manufacturer 90-degree door projection A.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

18 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Niche width in inches (mm), min. -> 18 (457)

Why this value was used

Niche width in inches (mm), min. -> 18 (457)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Product sheet
assets.skulytics.io · Product sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.

Why this value was used

Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.

Other evidence found

• 84 in — superseded

  105807510.pdf; page 32. Model scope: not separately recorded. Raw value: MasterCool II installation instructions state the standard niche height is 84 in; applied to documented F24x2 family geometry.. The final reviewed registry supersedes this earlier audit value. Exact-model US Miele product sheet explicitly states min_cutout_height_in=84.125 in; supersedes prior metric-normalized/family value 84.0.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Product sheet
assets.skulytics.io · Product sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.875 in; supersedes prior metric-normalized/family value 24.75.

Why this value was used

Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.875 in; supersedes prior metric-normalized/family value 24.75.

Other evidence found

• 24.75 in — superseded

  74524102.pdf; page 1. Model scope: not separately recorded. Raw value: Exact-model Miele product sheet: niche depth 629 mm; normalized to nearest 1/8 in = 24.75 in.. The final reviewed registry supersedes this earlier audit value. Exact-model US Miele product sheet explicitly states min_cutout_depth_in=24.875 in; supersedes prior metric-normalized/family value 24.75.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: medium.

Calculation inputs: Cabinet case width; Overall width; Minimum cutout width;

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Per-side cavity reveal derived from verified niche width 18 in minus widest closed appliance width 17.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 18 (457)

Why this value was used

Per-side cavity reveal derived from verified niche width 18 in minus widest closed appliance width 17.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 18 (457) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2

Confidence label: medium.

Calculation inputs: Cabinet case width; Overall width; Minimum cutout width;

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Per-side cavity reveal derived from verified niche width 18 in minus widest closed appliance width 17.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 18 (457)

Why this value was used

Per-side cavity reveal derived from verified niche width 18 in minus widest closed appliance width 17.875 in, divided by two = 0.0625 in. Base evidence: Niche width in inches (mm), min. -> 18 (457) Calculation or inference: (min_cutout_width_in - max(case_width_in,width_doors_closed_in)) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - max(height_case_in,height_hinge_in)

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Miele F2472VI Product sheet
assets.skulytics.io · Product sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Recomputed from exact-model US product sheet: 84.125 in niche dimension minus 83.75 in verified appliance dimension = 0.375 in; supersedes prior value 0.25.

Why this value was used

Recomputed from exact-model US product sheet: 84.125 in niche dimension minus 83.75 in verified appliance dimension = 0.375 in; supersedes prior value 0.25. Calculation or inference: min_cutout_height_in - max(height_case_in,height_hinge_in).

Other evidence found

• 0.25 in — superseded

  105807510.pdf; page 32. Model scope: not separately recorded. Raw value: Top cavity delta: documented 84-in standard niche height minus 83 3/4-in appliance height = 1/4 in.. The final reviewed registry supersedes this earlier audit value. Recomputed from exact-model US product sheet: 84.125 in niche dimension minus 83.75 in verified appliance dimension = 0.375 in; supersedes prior value 0.25.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: medium.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Miele F2472VI Product sheet
assets.skulytics.io · Product sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Recomputed from exact-model US product sheet: 24.875 in niche dimension minus 24 in verified appliance dimension = 0.875 in; supersedes prior value 0.75.

Why this value was used

Recomputed from exact-model US product sheet: 24.875 in niche dimension minus 24 in verified appliance dimension = 0.875 in; supersedes prior value 0.75. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

• 0.75 in — superseded

  74524102.pdf; page 1. Model scope: not separately recorded. Raw value: Rear cavity delta from exact-model sheet: normalized niche depth 24.75 in minus verified case-only depth 24 in = 0.75 in.. The final reviewed registry supersedes this earlier audit value. Recomputed from exact-model US product sheet: 24.875 in niche dimension minus 24 in verified appliance dimension = 0.875 in; supersedes prior value 0.75.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2412SFSS Operating and Installation instructions PDF
assets.skulytics.io · Operating and Installation instructions PDF
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-05

Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

17.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2472VI Operating and Installation instructions
assets.skulytics.io · Operating and Installation instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Appliance width in in.(mm) -> 17 7/8 (451)

Why this value was used

Appliance width in in.(mm) -> 17 7/8 (451)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Miele F2412SFSS Operating and Installation instructions PDF
assets.skulytics.io · Operating and Installation instructions PDF
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 23
Reviewed: 2026-09-04

Manufacturer 90-degree opening diagram: 3/8 in (10 mm) to adjoining wall.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.