This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Top Freezer · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-22. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.5 in | ✓ Verified — retained secondary source | Midea installation document — 92267683.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 92267683.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 65.6 in | ✓ Verified — retained secondary source | Midea installation document — 92267683.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit65.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 92267683.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.6 in | ✓ Verified — retained secondary source | Midea installation document — 92267683.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit66.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 92267683.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 27.7559 in | ✓ Conflicting sources — resolved · Calculated/inferred | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit27.7559 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared 750-mm Midea cabinet platform Confidence label: medium. Primary evidenceMidea measurement source — 105608414.pdf Shared 30-in cabinet body depth; exact external width/depth/height agree.Open original source ↗ Why this value was usedShared 30-in cabinet body depth; exact external width/depth/height agree. Calculation or inference: shared 750-mm Midea cabinet platform. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 30.9 in | ✓ Verified — retained secondary source | Midea installation document — 92267683.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit30.9 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 92267683.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 30.9 in | ✓ Verified — retained secondary source | Midea installation document — 92267683.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit30.9 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 92267683.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 57.2559 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 92267683.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit57.2559 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 27.7559 + 29.5 Confidence label: medium. Primary evidenceMidea measurement source — 92267683.pdf Single-door 90-degree geometric envelope from cabinet depth and width.Open original source ↗ Why this value was usedSingle-door 90-degree geometric envelope from cabinet depth and width. Calculation or inference: 27.7559 + 29.5. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.5 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 92267683.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit35.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.5 + 2 * 3.0 Confidence label: medium. Primary evidenceMidea measurement source — 92267683.pdf Width plus documented 3-in clearance on each side.Open original source ↗ Why this value was usedWidth plus documented 3-in clearance on each side. Calculation or inference: 29.5 + 2 * 3.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.6 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 92267683.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit69.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceMidea measurement source — 92267683.pdf Minimum opening height derived from highest appliance endpoint 66.6 in plus documented top clearance 3.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest appliance endpoint 66.6 in plus documented top clearance 3.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 30.7559 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608341.pdf brandsmartusa.com | Page 6 | |
Value used by ExactFit30.7559 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceMidea measurement source — 105608341.pdf Midea user manual (MRT18S3AWW, MRT18S3ABB, MRT18S3AST) p.6 Recommended Clearance: 3" (7.6 cm) at the top, back and both sides; cabinet depth 27.7559 in + 3 in = 30.7559 in, as for the other finishes. Replaces the retailer "Cutout Depth" 28.25 in, which is shallower than the cabinet plus the printed rear space.Open original source ↗ Why this value was usedMidea user manual (MRT18S3AWW, MRT18S3ABB, MRT18S3AST) p.6 Recommended Clearance: 3" (7.6 cm) at the top, back and both sides; cabinet depth 27.7559 in + 3 in = 30.7559 in, as for the other finishes. Replaces the retailer "Cutout Depth" 28.25 in, which is shallower than the cabinet plus the printed rear space. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 3 in | ✓ Verified — retained secondary source | Midea measurement source — 92267683.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceMidea measurement source — 92267683.pdf Legacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 3 in | ✓ Verified — retained secondary source | Midea measurement source — 92267683.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceMidea measurement source — 92267683.pdf Legacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['both sides']; Exact manual recommends 3 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 92267683.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: declared_multi_model_scope Confidence label: medium. Primary evidenceMidea measurement source — 92267683.pdf 7.6 cm) Clearance at the topOpen original source ↗ Why this value was used7.6 cm) Clearance at the top Calculation or inference: cached document family mapping: declared_multi_model_scope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 3 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 92267683.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceMidea measurement source — 92267683.pdf Manufacturer family manual specifies 3 in clearance at the top, rear, and sides.Open original source ↗ Why this value was usedManufacturer family manual specifies 3 in clearance at the top, rear, and sides. Calculation or inference: cached documented shared chassis propagation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.5 in | ✓ Verified — retained secondary source | Midea installation document — 92267683.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit29.5 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 92267683.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 27.7559 in. Earlier retained values: 27.7656 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Shared 30-in cabinet body depth; exact external width/depth/height agree. Calculation or inference: shared 750-mm Midea cabinet platform.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: MRT18S3AST. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: MRT18S3AST. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth without door.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗brandsmartusa.com · Web source · secondary model/source
Model numbers covered: MRT18S3AST. Publication/revision date: Not recorded. Reviewed: 2026-10-22.
1 displayed measurements supported: Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.