This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.8 in | ✓ Verified — retained secondary source | Midea installation document — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.8 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105614586.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.7 in | ✓ Conflicting sources — resolved | Midea installation document — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit67.7 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105614586.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.9 in | ✓ Verified — retained secondary source | Midea installation document — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit69.9 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105614586.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25 in | ✓ Verified — retained secondary source | Midea installation document — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105614586.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.9 in | ✓ Verified — retained secondary source | Midea installation document — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.9 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105614586.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.9 in | ✓ Verified — retained secondary source | Midea installation document — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.9 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105614586.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 42.9 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit42.9 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25.0 + 35.8 / 2 Confidence label: medium. Primary evidenceMidea measurement source — 105614586.pdf Side-by-side 90-degree geometric envelope using exact cabinet depth and half-width door leaf.Open original source ↗ Why this value was usedSide-by-side 90-degree geometric envelope using exact cabinet depth and half-width door leaf. Calculation or inference: 25.0 + 35.8 / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 43.674 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105614584.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit43.674 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.8 + 2 * 3.937 Confidence label: medium. Primary evidenceMidea measurement source — 105614584.pdf Width plus documented >100 mm clearance on each side.Open original source ↗ Why this value was usedWidth plus documented >100 mm clearance on each side. Calculation or inference: 35.8 + 2 * 3.937. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 73.837 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105614584.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit73.837 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceMidea measurement source — 105614584.pdf Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.Open original source ↗ Why this value was usedMinimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 27.953 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105614584.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit27.953 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceMidea measurement source — 105614584.pdf Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 2.953 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 2.953 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 3.937 in | ✓ Verified — retained secondary source | Midea measurement source — 105614584.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3.937 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceMidea measurement source — 105614584.pdf SIDES | >100mm | TOPOpen original source ↗ Why this value was usedSIDES | >100mm | TOP Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 3.937 in | ✓ Verified — retained secondary source | Midea measurement source — 105614584.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3.937 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceMidea measurement source — 105614584.pdf SIDES | >100mm | TOPOpen original source ↗ Why this value was usedSIDES | >100mm | TOP Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3.937 in | ✓ Verified — retained secondary source | Midea measurement source — 105614584.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3.937 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea measurement source — 105614584.pdf Exact-model manufacturer manual specifies over 100 mm top/side clearance and 50-75 mm rear spacing.Open original source ↗ Why this value was usedExact-model manufacturer manual specifies over 100 mm top/side clearance and 50-75 mm rear spacing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2.953 in | ✓ Verified — retained secondary source | Midea measurement source — 105614584.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit2.953 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceMidea measurement source — 105614584.pdf BACK | 50-75mm | SIDESOpen original source ↗ Why this value was usedBACK | 50-75mm | SIDES Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.8 in | ✓ Verified — retained secondary source | Midea installation document — 105614586.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.8 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105614586.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 67.7 in. Earlier retained values: 69.9 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model or explicitly covered Midea dimensional source.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: MRS25I7BST. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: MRS25I7BST. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
7 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.