This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Top Freezer · Compact
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-28. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 18.5 in | ✓ Verified — retained secondary source | Midea installation document — 105608430.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit18.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608430.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 46.9 in | ✓ Verified — retained secondary source | Midea installation document — 105608430.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit46.9 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608430.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 46.9 in | ✓ Conflicting sources — resolved | Midea installation document — 105608430.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit46.9 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608430.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 20.1 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608432.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit20.1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: standardized compact flush-door envelope Confidence label: medium. Primary evidenceMidea measurement source — 105608432.pdf No separate cabinet-only endpoint is published; standardized to the compact flush-door depth.Open original source ↗ Why this value was usedNo separate cabinet-only endpoint is published; standardized to the compact flush-door depth. Calculation or inference: standardized compact flush-door envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 20.1 in | ✓ Verified — retained secondary source | Midea installation document — 105608430.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit20.1 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608430.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 20.1 in | ✓ Conflicting sources — resolved | Midea installation document — 105608430.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit20.1 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608430.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 38.6 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608432.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit38.6 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 20.1 + 18.5 Confidence label: medium. Primary evidenceMidea measurement source — 105608432.pdf Single-door 90-degree geometric envelope from exact compact dimensions.Open original source ↗ Why this value was usedSingle-door 90-degree geometric envelope from exact compact dimensions. Calculation or inference: 20.1 + 18.5. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 26.5 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608430.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit26.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 18.5 + 2 * 4.0 Confidence label: medium. Primary evidenceMidea measurement source — 105608430.pdf Width plus documented 4-in clearance on each side.Open original source ↗ Why this value was usedWidth plus documented 4-in clearance on each side. Calculation or inference: 18.5 + 2 * 4.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 57.65 in | ✓ Conflicting sources — resolved · Calculated/inferred | Midea measurement source — 105608430.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit57.65 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: high. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceMidea measurement source — 105608430.pdf Recalculated 2026-09-28 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 46.9, height_hinge_in = 46.9, top_clearance_in = 10.75 = 57.65 in (previously 58.711 in).Open original source ↗ Why this value was usedRecalculated 2026-09-28 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 46.9, height_hinge_in = 46.9, top_clearance_in = 10.75 = 57.65 in (previously 58.711 in). Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24.1 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608430.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit24.1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceMidea measurement source — 105608430.pdf Minimum opening depth derived from case-only depth 20.1 in plus documented rear clearance 4.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 20.1 in plus documented rear clearance 4.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 4 in | ✓ Verified — retained secondary source | Midea measurement source — 105608430.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceMidea measurement source — 105608430.pdf Legacy reviewed field migration; endpoint indicators=['both sides']; Manual requires 4 in at both sides.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['both sides']; Manual requires 4 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 4 in | ✓ Verified — retained secondary source | Midea measurement source — 105608430.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceMidea measurement source — 105608430.pdf Legacy reviewed field migration; endpoint indicators=['both sides']; Manual requires 4 in at both sides.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['both sides']; Manual requires 4 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 10.75 in | ✓ Conflicting sources — resolved | Midea measurement source — 105608430.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit10.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea measurement source — 105608430.pdf Recommended clearance above the appliance: 10 3/4 in, printed on this model's own sheet. The stored 11.811 in is 300 mm, which the document does not state.Open original source ↗ Why this value was usedRecommended clearance above the appliance: 10 3/4 in, printed on this model's own sheet. The stored 11.811 in is 300 mm, which the document does not state. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 4 in | ✓ Verified — retained secondary source | Midea measurement source — 105608430.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea measurement source — 105608430.pdf 4" (10 cm) Clearance at the backOpen original source ↗ Why this value was used4" (10 cm) Clearance at the back Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 18.5 in | ✓ Verified — retained secondary source | Midea installation document — 105608430.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit18.5 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608430.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 46.9 in. Earlier retained values: 46.8 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model or explicitly covered Midea dimensional source.
View source scope, location, and impact on fitSelected: 20.1 in. Earlier retained values: 20 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model or explicitly covered Midea dimensional source.
View source scope, location, and impact on fitSelected: 57.65 in. Earlier retained values: 58.711 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Recalculated 2026-09-28 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 46.9, height_hinge_in = 46.9, top_clearance_in = 10.75 = 57.65 in (previously 58.711 in). Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
View source scope, location, and impact on fitSelected: 10.75 in. Earlier retained values: 11.811 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Recommended clearance above the appliance: 10 3/4 in, printed on this model's own sheet. The stored 11.811 in is 300 mm, which the document does not state.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: MRM45D3ASL. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: MRM45D3ASL. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Depth without door; Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-28. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.