Measurement evidence for Midea MRF32I6BST

Value used by ExactFit

35.8 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea installation document — 104687286.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

Exact-model or explicitly covered Midea dimensional source.

Other evidence found

• 35.83 in — superseded

  Document 105608617.pdf; page 4. Model scope: not separately recorded. Raw value: W x D x H) 35.83 x 29.02 x 69.88in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.9 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea installation document — 104687286.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

Exact-model or explicitly covered Midea dimensional source.

Other evidence found

• 69.88 in — superseded

  Document 105608617.pdf; page 4. Model scope: not separately recorded. Raw value: W x D x H) 35.83 x 29.02 x 69.88in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.9 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea installation document — 104687286.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

Exact-model or explicitly covered Midea dimensional source.

Other evidence found

• 69.88 in — superseded

  Document 105608617.pdf; page 4. Model scope: not separately recorded. Raw value: W x D x H) 35.83 x 29.02 x 69.88in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea installation document — 104687286.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

Exact-model or explicitly covered Midea dimensional source.

Other evidence found

• 29.2656 in — superseded

  www.ajmadison.com; location not retained. Model scope: not separately recorded. Raw value: Depth without Door = 29.2656 in | RF32I6BST 36 Inch Freestanding French Door ... Width: 35 4/5". Depth: 33 7/10". Depth without Door: 29 17/64". Depth with Door Open 90°: 49 1/64". Height: 69 9/10". Height without Hinges: 6. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.7 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea installation document — 104687286.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

Exact-model or explicitly covered Midea dimensional source.

Other evidence found

• 29.02 in — superseded

  Document 105608617.pdf; page 4. Model scope: not separately recorded. Raw value: W x D x H) 35.83 x 29.02 x 69.88in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.7 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea installation document — 104687286.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

Exact-model or explicitly covered Midea dimensional source.

Other evidence found

• 29.02 in — superseded

  Document 105608617.pdf; page 4. Model scope: not separately recorded. Raw value: W x D x H) 35.83 x 29.02 x 69.88in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

49.0156 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Midea measurement source — MRF32I6BST.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model listing states Depth with Door Open 90 degrees = 49 1/64 in.
Reviewed: 2026-09-04

Cached exact-model listing states Depth with Door Open 90 degrees = 49 1/64 in.

Why this value was used

Cached exact-model listing states Depth with Door Open 90 degrees = 49 1/64 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.05 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.8 + 2 * 0.125

Confidence label: medium.

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

Width plus documented >1/8-in installation clearance each side.

Why this value was used

Width plus documented >1/8-in installation clearance each side. Calculation or inference: 35.8 + 2 * 0.125.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.9 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.

Why this value was used

Minimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Minimum opening depth is the verified cabinet depth plus the documented rear clearance.

Why this value was used

Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Why this value was used

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Why this value was used

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Why this value was used

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Why this value was used

Exact-model manufacturer manual specifies 1 in top, 2 in rear, and 1/8 in side clearances.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics

Confidence label: high.

Primary evidence

Midea measurement source — 105608617.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Legacy reviewed field migration; endpoint indicators=['side wall']; Exact manual requires more than 1-1/2 in when placed against a side wall.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Legacy reviewed field migration; endpoint indicators=['side wall']; Exact manual requires more than 1-1/2 in when placed against a side wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.8 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Midea installation document — 104687286.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Exact-model or explicitly covered Midea dimensional source.

Why this value was used

Exact-model or explicitly covered Midea dimensional source.

Other evidence found

• 35.83 in — superseded

  Document 105608617.pdf; page 4. Model scope: not separately recorded. Raw value: W x D x H) 35.83 x 29.02 x 69.88in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.