This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.5276 in | ✓ Conflicting sources — resolved | Midea installation document — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit29.5276 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608414.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 66.6142 in | ✓ Verified — retained secondary source | Midea installation document — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit66.6142 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608414.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.6142 in | ✓ Conflicting sources — resolved | Midea installation document — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit66.6142 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608414.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 27.7559 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit27.7559 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 705 mm / 25.4 Confidence label: medium. Primary evidenceMidea measurement source — 105608414.pdf Diagram endpoint C1 is the body envelope although the English table label is mistranslated.Open original source ↗ Why this value was usedDiagram endpoint C1 is the body envelope although the English table label is mistranslated. Calculation or inference: 705 mm / 25.4. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 30.9055 in | ✓ Verified — retained secondary source | Midea installation document — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit30.9055 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608414.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 30.9055 in | ✓ Conflicting sources — resolved | Midea installation document — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit30.9055 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608414.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 58.375 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — MRB19B7AST.html www.ajmadison.com | Retained specification excerpt: Propagated from exact MRB19B7 90-degree listing; exterior dimensions match. | |
Value used by ExactFit58.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared MRB19B5/B7 exterior chassis Confidence label: medium. Primary evidenceMidea measurement source — MRB19B7AST.html Propagated from exact MRB19B7 90-degree listing; exterior dimensions match.Open original source ↗ Why this value was usedPropagated from exact MRB19B7 90-degree listing; exterior dimensions match. Calculation or inference: shared MRB19B5/B7 exterior chassis. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 37.4016 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 5 | |
Value used by ExactFit37.4016 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.5276 + 2 * 3.937 Confidence label: medium. Primary evidenceMidea measurement source — 105608414.pdf Width plus documented >100 mm clearance on each side.Open original source ↗ Why this value was usedWidth plus documented >100 mm clearance on each side. Calculation or inference: 29.5276 + 2 * 3.937. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.6142 in | ✓ Verified — equivalent model · Calculated/inferred | Midea measurement source — saved-openparser:opj_zlWO3gS2ri3m_j742aDDP_0.json#ecb6171e45d820c0f8cddc30c3ab32f1 assets.skulytics.io | Page 1 | |
Value used by ExactFit69.6142 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceMidea measurement source — saved-openparser:opj_zlWO3gS2ri3m_j742aDDP_0.json#ecb6171e45d820c0f8cddc30c3ab32f1 Minimum opening height derived from highest appliance endpoint 66.6142 in plus propagated top clearance 3.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest appliance endpoint 66.6142 in plus propagated top clearance 3.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Why evidence from MRB19B7AST appliesTarget model: MRB19B5AST. Supporting model: MRB19B7AST. Manufacturer: Midea. Product family and measurement relationship: max(height_case_in,height_hinge_in) + top_clearance_in. Measurement transferred: Minimum cutout height. Relevant equivalence evidence: Minimum opening height derived from highest appliance endpoint 66.6142 in plus propagated top clearance 3.0 in.. Known differences: not separately recorded. Reviewed 2026-09-17. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 30.7559 in | ✓ Verified — retained secondary source · Calculated/inferred | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit30.7559 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceMidea measurement source — 105608414.pdf Minimum opening depth is the verified cabinet depth plus the documented rear clearance.Open original source ↗ Why this value was usedMinimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 3 in | ✓ Verified — retained secondary source | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea measurement source — 105608414.pdf Manufacturer family material specifies 3 in clearance at the top, rear, and both sides.Open original source ↗ Why this value was usedManufacturer family material specifies 3 in clearance at the top, rear, and both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 3 in | ✓ Verified — retained secondary source | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea measurement source — 105608414.pdf Manufacturer family material specifies 3 in clearance at the top, rear, and both sides.Open original source ↗ Why this value was usedManufacturer family material specifies 3 in clearance at the top, rear, and both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3 in | ✓ Verified — equivalent model · Calculated/inferred | Midea measurement source — saved-openparser:opj_zlWO3gS2ri3m_j742aDDP_0.json#ecb6171e45d820c0f8cddc30c3ab32f1 assets.skulytics.io | Page 1 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Midea MRB19B7AST Confidence label: medium. Primary evidenceMidea measurement source — saved-openparser:opj_zlWO3gS2ri3m_j742aDDP_0.json#ecb6171e45d820c0f8cddc30c3ab32f1 Conflict-free corporate-family exact 8-dimension chassis match to Midea MRB19B7AST; original evidence: 7.6 cm) Clearance at the topOpen original source ↗ Why this value was usedConflict-free corporate-family exact 8-dimension chassis match to Midea MRB19B7AST; original evidence: 7.6 cm) Clearance at the top Calculation or inference: exact 8-dimension chassis signature; source model Midea MRB19B7AST. Why evidence from MRB19B7AST appliesTarget model: MRB19B5AST. Supporting model: MRB19B7AST. Manufacturer: Midea. Product family and measurement relationship: exact 8-dimension chassis signature; source model Midea MRB19B7AST. Measurement transferred: Top clearance. Relevant equivalence evidence: Conflict-free corporate-family exact 8-dimension chassis match to Midea MRB19B7AST; original evidence: 7.6 cm) Clearance at the top. Known differences: not separately recorded. Reviewed 2026-09-17. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 3 in | ✓ Verified — retained secondary source | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea measurement source — 105608414.pdf Manufacturer family material specifies 3 in clearance at the top, rear, and both sides.Open original source ↗ Why this value was usedManufacturer family material specifies 3 in clearance at the top, rear, and both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.937 in | ✓ Verified — retained secondary source | Midea measurement source — 105608414.pdf assets.skulytics.io | Page 5 | |
Value used by ExactFit3.937 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceMidea measurement source — 105608414.pdf Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). • Too small of a distance from adjacent items may result in the degradation | of freezing capability and increased electricity costs. Allow over 100 mm of | clearance from each adjacent wall when installing the appliance.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). • Too small of a distance from adjacent items may result in the degradation | of freezing capability and increased electricity costs. Allow over 100 mm of | clearance from each adjacent wall when installing the appliance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.5276 in | ✓ Verified — retained secondary source | Midea installation document — 105608414.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit29.5276 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceMidea installation document — 105608414.pdf Exact-model or explicitly covered Midea dimensional source.Open original source ↗ Why this value was usedExact-model or explicitly covered Midea dimensional source. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 29.5276 in. Earlier retained values: 29.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model or explicitly covered Midea dimensional source.
View source scope, location, and impact on fitSelected: 66.6142 in. Earlier retained values: 66.6 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model or explicitly covered Midea dimensional source.
View source scope, location, and impact on fitSelected: 30.9055 in. Earlier retained values: 30.9 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model or explicitly covered Midea dimensional source.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: MRB19B5AST. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Minimum cutout width; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.ajmadison.com · Web source · secondary model/source
Model numbers covered: MRB19B5AST. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · equivalent model/source
Model numbers covered: MRB19B7AST. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout height; Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.