Measurement evidence for Maytag MRTX5121TZ

Value used by ExactFit

32.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — p.33-inch-wide-top-freezer-refrigerator-with-garage-mode-21-cu.-ft.mrtx5121tz.html
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: net Width: 32.5 in | No Water Filter Indicator/Reset No Water Filter Location N/A ### Dimensions Cab
Reviewed: 2026-09-04

net Width: 32.5 in | No Water Filter Indicator/Reset No Water Filter Location N/A ### Dimensions Cabinet Width 32.5 in Depth 34.125 in Depth Closed Excluding Handles 31.875 in Depth Closed Including

Why this value was used

net Width: 32.5 in | No Water Filter Indicator/Reset No Water Filter Location N/A ### Dimensions Cabinet Width 32.5 in Depth 34.125 in Depth Closed Excluding Handles 31.875 in Depth Closed Including

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

65.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Official exact-family table: Height to top of cabinet = 65 1/2 in.

Why this value was used

Official exact-family table: Height to top of cabinet = 65 1/2 in.

Other evidence found

• 66 in — superseded

  www.ajmadison.com; location not retained. Model scope: not separately recorded. Raw value: h Door at 90°: 36 11/25 Inch Height: 66 1/16 Inch Height without Hinges: 66 Inch Shabbos Compliance Sabbath Mode: No Smart WiFi:. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Official exact-family table: Overall Height = 66 1/4 in.

Why this value was used

Official exact-family table: Overall Height = 66 1/4 in.

Other evidence found

• 66 in — superseded

  www.maytag.com; location not retained. Model scope: not separately recorded. Raw value: Height To Top Of Door Hinge: 66.0 in | pacity Volume 6.07 cu. ft. Height 66.0625 in Height To Top Of Cabinet 65.313 in Height To Top Of Door Hinge 66 in Height To Top Of Door Trim 66.063 in Maximum Height 66.0625 in Minimum Height 6. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Official exact-family table: Depth of cabinet only = 27 7/8 in.

Why this value was used

Official exact-family table: Depth of cabinet only = 27 7/8 in.

Other evidence found

• 27.81 in — superseded

  www.maytag.com; location not retained. Model scope: not separately recorded. Raw value: Depth Excluding Doors: 27.81 in | pth Closed Excluding Handles 31.875 in Depth Closed Including Handles 34.125 in Depth Excluding Doors 27.813 in Depth With Door Open 90 Degree 61.875 in Depth-Drawer Open 61.875 in Freezer Ca. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Official exact-family table: Depth without handles = 31 7/8 in.

Why this value was used

Official exact-family table: Depth without handles = 31 7/8 in.

Other evidence found

• 31.88 in — superseded

  www.maytag.com; location not retained. Model scope: not separately recorded. Raw value: Depth Closed Excluding Handles: 31.88 in | Water Filter Location N/A ### Dimensions Cabinet Width 32.5 in Depth 34.125 in Depth Closed Excluding Handles 31.875 in Depth Closed Including Handles 34.125 in Depth Excluding Doors 27.813 in Depth . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.4375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Official exact-family table: Depth with handles = 34 7/16 in.

Why this value was used

Official exact-family table: Depth with handles = 34 7/16 in.

Other evidence found

• 34.12 in — superseded

  www.maytag.com; location not retained. Model scope: not separately recorded. Raw value: Depth Closed Including Handles: 34.12 in | Cabinet Width 32.5 in Depth 34.125 in Depth Closed Excluding Handles 31.875 in Depth Closed Including Handles 34.125 in Depth Excluding Doors 27.813 in Depth With Door Open 90 Degree 61.875 in Depth-. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

61.875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — p.33-inch-wide-top-freezer-refrigerator-with-garage-mode-21-cu.-ft.mrtx5121tz.html
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth With Door Open 90 = 61.875 in | 875 in Depth Closed Including Handles 34.125 in Depth Excludin
Reviewed: 2026-09-04

Depth With Door Open 90 = 61.875 in | 875 in Depth Closed Including Handles 34.125 in Depth Excluding Doors 27.813 in Depth With Door Open 90 Degree 61.875 in Depth-Drawer Open 61.875 in Freezer Capacity Volume 6.07 cu. ft. Height 66.0625

Why this value was used

Depth With Door Open 90 = 61.875 in | 875 in Depth Closed Including Handles 34.125 in Depth Excluding Doors 27.813 in Depth With Door Open 90 Degree 61.875 in Depth-Drawer Open 61.875 in Freezer Capacity Volume 6.07 cu. ft. Height 66.0625

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 32.5 + 2 * 0.5

Confidence label: medium.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening from printed cabinet width plus explicit 0.5 in ventilation space on each side: 32.5
Reviewed: 2026-09-04

Minimum opening from printed cabinet width plus explicit 0.5 in ventilation space on each side: 32.5 + 2 * 0.5 = 33.5 in

Why this value was used

Minimum opening from printed cabinet width plus explicit 0.5 in ventilation space on each side: 32.5 + 2 * 0.5 = 33.5 in Calculation or inference: 32.5 + 2 * 0.5.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in, height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Installation envelope: max(case 65.5, hinge 66.25) + 0.5 in top = 66.75 in.

Why this value was used

Installation envelope: max(case 65.5, hinge 66.25) + 0.5 in top = 66.75 in. Calculation or inference: max(height_case_in, height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Installation envelope: 27.875 in case depth + 1 in rear = 28.875 in.

Why this value was used

Installation envelope: 27.875 in case depth + 1 in rear = 28.875 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRTX5121T***

Confidence label: medium.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern MRTX5121T***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRTX5121T***

Confidence label: medium.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern MRTX5121T***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact MRTX5121 family guide: allow 1/2" between refrigerator top and overhead cabinets.

Why this value was used

Exact MRTX5121 family guide: allow 1/2" between refrigerator top and overhead cabinets.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact MRTX5121 family guide: allow at least 1" between back of cabinet and wall.

Why this value was used

Exact MRTX5121 family guide: allow at least 1" between back of cabinet and wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Maytag measurement source — dimension-guide-w11821764-reva.pdf
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or le
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Official family dimension guide: next to a fixed wall, leave 2 in minimum on hinge side

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Official family dimension guide: next to a fixed wall, leave 2 in minimum on hinge side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.5 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Maytag measurement source — p.33-inch-wide-top-freezer-refrigerator-with-garage-mode-21-cu.-ft.mrtx5121tz.html
Maytag · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cabinet Width = 32.5 in | ver No Water Filter Indicator/Reset No Water Filter Location N/A ### Dimen
Reviewed: 2026-09-04

Cabinet Width = 32.5 in | ver No Water Filter Indicator/Reset No Water Filter Location N/A ### Dimensions Cabinet Width 32.5 in Depth 34.125 in Depth Closed Excluding Handles 31.875 in Depth Closed Including

Why this value was used

Cabinet Width = 32.5 in | ver No Water Filter Indicator/Reset No Water Filter Location N/A ### Dimensions Cabinet Width 32.5 in Depth 34.125 in Depth Closed Excluding Handles 31.875 in Depth Closed Including

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.