This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-29. 6 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105422796.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105422796.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105422796.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth Excluding Doors: 23.88 in | epth Closed Excluding Handles 28.375 in Depth Closed Including Han
Value used by ExactFit
23.88 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — p.36-inch-wide-counter-depth-side-by-side-refrigerator-with-arctic-blue-interior-20.8-cu.-ft.mrsc6636rz.html Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Excluding Doors: 23.88 in | epth Closed Excluding Handles 28.375 in Depth Closed Including Han Reviewed: 2026-09-04
Depth Excluding Doors: 23.88 in | epth Closed Excluding Handles 28.375 in Depth Closed Including Handles 30.75 in Depth Excluding Doors 23.875 in Depth With Door Open 90 Degree 45.75 in Freezer Capacity Volume 7.19 cu. ft. Gr
Depth Excluding Doors: 23.88 in | epth Closed Excluding Handles 28.375 in Depth Closed Including Handles 30.75 in Depth Excluding Doors 23.875 in Depth With Door Open 90 Degree 45.75 in Freezer Capacity Volume 7.19 cu. ft. Gr
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105422796.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105422796.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105422796.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — 105422797.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-19
Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm) is recommended. (Replaces the product web page's 36.5 in.)
Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm) is recommended. (Replaces the product web page's 36.5 in.)
Other evidence found
36.5 in — superseded
www.maytag.com; location not retained. Model scope: not separately recorded. Raw value: Cutout Width: 36.5 in | th 35.5 in Capacity 20.85 cu. ft. Cutout Depth 30.375 in Cutout Height 70.25 in Cutout Width 36.5 in Depth 28.375 in Depth Closed Excluding Handles 28.375 in Depth Closed Including. The final reviewed registry supersedes this earlier audit value.
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Maytag measurement source — maytag-36-inch-wide-counter-depth-side-by-side-refrigerator-with-arctic-blue-interior-20-8-cu-ft-mrsc6636rz arkona-appliances.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Height 70.25" Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Maytag measurement source — dimension-guide-w11753392-revc.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
Minimum opening depth derived from case-only depth 23.88 in plus documented rear clearance 1.0 in.
Minimum opening depth derived from case-only depth 23.88 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — 105422797.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-29
This model's own Maytag manual, page 5: "allow for 1/2" (1.27 cm) of space on each side and at the top."
This model's own Maytag manual, page 5: "allow for 1/2" (1.27 cm) of space on each side and at the top."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — 105422797.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-29
This model's own Maytag manual, page 5: "allow for 1/2" (1.27 cm) of space on each side and at the top."
This model's own Maytag manual, page 5: "allow for 1/2" (1.27 cm) of space on each side and at the top."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
Maytag measurement source — 103455894.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-05
1.27 cm) of space on each side and at the top Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRSC6636R***
Confidence label: medium.
Primary evidence
Maytag measurement source — dimension-guide-w11753392-revc.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1" of space behind Calculation or inference: documented DOE model pattern MRSC6636R***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
Maytag measurement source — 103455894.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105422796.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Selected: 36 in. Earlier retained values: 36.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm) is recommended. (Replaces the product web page's 36.5 in.)
Model numbers covered: MRSC6636RZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
7 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
