This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-31. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Retained specification excerpt: net Width = 35.9375 in | Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dimensions
Value used by ExactFit
35.9375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — p.MRMF5436TZ.html Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: net Width = 35.9375 in | Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dimensions Reviewed: 2026-09-04
net Width = 35.9375 in | Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dimensions Cabinet Width 35.938 in Capacity 28.9 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36
net Width = 35.9375 in | Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dimensions Cabinet Width 35.938 in Capacity 28.9 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 106163212.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height To Top Of Door Hinge = 70.0625 in | u. ft. Gross Weight 326.28 lbs Height 70.0625 in Height T
Value used by ExactFit
70.0625 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — p.MRMF5436TZ.html Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Height To Top Of Door Hinge = 70.0625 in | u. ft. Gross Weight 326.28 lbs Height 70.0625 in Height T Reviewed: 2026-09-04
Height To Top Of Door Hinge = 70.0625 in | u. ft. Gross Weight 326.28 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height 69 in Net Weight 295.42 lbs Refrigerat
Height To Top Of Door Hinge = 70.0625 in | u. ft. Gross Weight 326.28 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height 69 in Net Weight 295.42 lbs Refrigerat
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 106163212.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 106163212.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 36.81 in. Context:
Value used by ExactFit
36.81 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — p.MRMF5436TZ.html Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 36.81 in. Context: Reviewed: 2026-09-04
Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 36.81 in. Context: Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excluding Handles 34.75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Ca
Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 36.81 in. Context: Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excluding Handles 34.75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Ca
Other evidence found
37.125 in — superseded
Document 106163212.pdf; page 1. Model scope: not separately recorded. Raw value: Depth with door handle -> 37
1/8"(942.8 mm). The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Retained specification excerpt: Depth With Door Open 90 = 49.0 in | .75 in Depth Closed Including Handles 36.813 in Depth Excluding
Value used by ExactFit
49 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — p.MRMF5436TZ.html Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door Open 90 = 49.0 in | .75 in Depth Closed Including Handles 36.813 in Depth Excluding Reviewed: 2026-09-04
Depth With Door Open 90 = 49.0 in | .75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 326.28 lbs Height 70.0625 in
Depth With Door Open 90 = 49.0 in | .75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 326.28 lbs Height 70.0625 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
36.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 35.9375 + 2 * 0.5 = 36.9375
Confidence label: high.
Primary evidence
Maytag measurement source — dimension-guide-w11817848-reva.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-31
Maytag's installation documents for MRMF5436TZ print no cutout width; they ask for 1/2 in of space on each side: guide: '1/2" space on each side' Opening width = 35.9375 + 1/2 + 1/2 = 36.9375 in. The earlier 36.188 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).
Maytag's installation documents for MRMF5436TZ print no cutout width; they ask for 1/2 in of space on each side: guide: '1/2" space on each side' Opening width = 35.9375 + 1/2 + 1/2 = 36.9375 in. The earlier 36.188 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 35.9375 + 2 * 0.5 = 36.9375.
Other evidence found
36.188 in — superseded
appliancehomestore.com; location not retained. Model scope: not separately recorded. Raw value: on Size | 36 in | | Cutout Height | 70.188 in | | Cutout Width | 36.188 in | | Depth | 36.8125 in | | Depth Closed Excluding. The final reviewed registry supersedes this earlier audit value.
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest stored appliance endpoint 70.0625 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRMF5436TZ
Confidence label: high.
Primary evidence
Maytag measurement source — dimension-guide-w11817848-reva.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern MRMF5436TZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRMF5436TZ
Confidence label: high.
Primary evidence
Maytag measurement source — dimension-guide-w11817848-reva.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern MRMF5436TZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRMF5436TZ
Confidence label: medium.
Primary evidence
Maytag measurement source — dimension-guide-w11817848-reva.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side and at the top Calculation or inference: documented DOE model pattern MRMF5436TZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern MRMF5436TZ
Confidence label: medium.
Primary evidence
Maytag measurement source — dimension-guide-w11817848-reva.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
2" space behind Calculation or inference: documented DOE model pattern MRMF5436TZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Maytag measurement source — 106163212.pdf Publisher not recorded
Page 2
Value used by ExactFit
14.0625 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — 106163212.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-14
NOTE: To allow for a full door swing, you will need to leave 14 1/16" (357 mm) of space between the refrigerator and the wall.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
NOTE: To allow for a full door swing, you will need to leave 14 1/16" (357 mm) of space between the refrigerator and the wall.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Retained specification excerpt: Cabinet Width = 35.938 in | ar® Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dim
Value used by ExactFit
35.938 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — p.MRMF5436TZ.html Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cabinet Width = 35.938 in | ar® Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dim Reviewed: 2026-09-04
Cabinet Width = 35.938 in | ar® Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dimensions Cabinet Width 35.938 in Capacity 28.9 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36
Cabinet Width = 35.938 in | ar® Qualified ENERGY STAR® Qualified Star K Certified Yes UL Yes ### Dimensions Cabinet Width 35.938 in Capacity 28.9 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Selected: 36.81 in. Earlier retained values: 37.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 36.81 in. Context: Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excluding Handles 34.75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Ca
Selected: 36.9375 in. Earlier retained values: 36.188 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Maytag's installation documents for MRMF5436TZ print no cutout width; they ask for 1/2 in of space on each side: guide: '1/2" space on each side' Opening width = 35.9375 + 1/2 + 1/2 = 36.9375 in. The earlier 36.188 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 35.9375 + 2 * 0.5 = 36.9375.
Model numbers covered: MRMF5436TZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
5 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-14.
5 displayed measurements supported: Cabinet height; Depth without door; Depth with door, without handles; Wall clearance for door open to 90°; Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-31. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
