This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-31. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
30.6063 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 29.6063 + 2 * 0.5 = 30.6063
Confidence label: high.
Primary evidence
Maytag measurement source — 105161571.pdf Maytag · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-31
Maytag's installation documents for MBF1958FEZ print no cutout width; they ask for 1/2 in of space on each side: guide: 'The document this model\'s measurements come from states: "allow for If the supply cord is damaged, it must be replaced by the 1/2" (1.25 cm) of space on each side and at the top."' Opening width = 29.6063 + 1/2 + 1/2 = 30.6063 in. The earlier 30.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).
Maytag's installation documents for MBF1958FEZ print no cutout width; they ask for 1/2 in of space on each side: guide: 'The document this model\'s measurements come from states: "allow for If the supply cord is damaged, it must be replaced by the 1/2" (1.25 cm) of space on each side and at the top."' Opening width = 29.6063 + 1/2 + 1/2 = 30.6063 in. The earlier 30.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 29.6063 + 2 * 0.5 = 30.6063.
Other evidence found
30 in — superseded
www.maytag.com; location not retained. Model scope: not separately recorded. Raw value: Cutout Width: 30.0 in | nsions. Cabinet Width. 29.625 in. Capacity. 18.67 cu. ft. Cutout Height. 67 in. Cutout Width. 30 in. Depth. 33.375 in. Depth Closed Excluding Handles. . The final reviewed registry supersedes this earlier audit value.
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Corrected installation envelope: max(65.5118 in cabinet, 67.0079 in overall/hinge height) + documented 0.5 in top clearance = 67.5079 in. Calculation or inference: max(height_case_in, height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Installation envelope: 28.1102 in case depth + 1 in documented rear space = 29.1102 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — 105161571.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-29
The document this model's measurements come from states: "allow for If the supply cord is damaged, it must be replaced by the 1/2" (1.25 cm) of space on each side and at the top."
The document this model's measurements come from states: "allow for If the supply cord is damaged, it must be replaced by the 1/2" (1.25 cm) of space on each side and at the top."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag measurement source — 105161571.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-29
The document this model's measurements come from states: "allow for If the supply cord is damaged, it must be replaced by the 1/2" (1.25 cm) of space on each side and at the top."
The document this model's measurements come from states: "allow for If the supply cord is damaged, it must be replaced by the 1/2" (1.25 cm) of space on each side and at the top."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: high.
Primary evidence
Maytag measurement source — 105161570.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05
1.25 cm) space on each side and at the top Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161571.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-05
Exact-model location requirements: allow 1" (2.54 cm) of space behind the refrigerator.
Exact-model location requirements: allow 1" (2.54 cm) of space behind the refrigerator.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
2.5 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: high.
Primary evidence
Maytag measurement source — 105161570.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave 2Z⁄x" (6.3 cm
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave 2Z⁄x" (6.3 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Maytag installation document — 105161570.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Selected: 30.6063 in. Earlier retained values: 30 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Maytag's installation documents for MBF1958FEZ print no cutout width; they ask for 1/2 in of space on each side: guide: 'The document this model\'s measurements come from states: "allow for If the supply cord is damaged, it must be replaced by the 1/2" (1.25 cm) of space on each side and at the top."' Opening width = 29.6063 + 1/2 + 1/2 = 30.6063 in. The earlier 30.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 29.6063 + 2 * 0.5 = 30.6063.
Model numbers covered: MBF1958FEZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
11 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Top clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-31. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
