This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Top Freezer · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-25. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 23.625 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit23.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf Width 23 5/8"Open original source ↗ Why this value was usedWidth 23 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 63.625 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit63.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf Height to Top of Case 63 5/8"Open original source ↗ Why this value was usedHeight to Top of Case 63 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 64.625 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit64.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf W x H x D) 23 5/8" x 64 5/8" x 28"Open original source ↗ Why this value was usedW x H x D) 23 5/8" x 64 5/8" x 28" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.625 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf Depth without Door 24 5/8"Open original source ↗ Why this value was usedDepth without Door 24 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf Depth without Handles 28"Open original source ↗ Why this value was usedDepth without Handles 28" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf W x H x D) 23 5/8" x 64 5/8" x 28"Open original source ↗ Why this value was usedW x H x D) 23 5/8" x 64 5/8" x 28" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 49.375 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit49.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf Depth (Total with 90˚ Door Open): 49.375 in | Depth (Total with 90˚ Door Open) | 49 3/8" | Installation ClearanceOpen original source ↗ Why this value was usedDepth (Total with 90˚ Door Open): 49.375 in | Depth (Total with 90˚ Door Open) | 49 3/8" | Installation Clearance Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 27.625 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 77836549.pdf + Specification%2BSheet + lt11c2000v + lg-lt11c2000v-top-freezer-refrigerator files.bbystatic.com | Page 1 | |
Value used by ExactFit27.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * exact-model installation side clearance Confidence label: medium. Calculation inputs: Overall width; Primary evidenceLG measurement source — 77836549.pdf + Specification%2BSheet + lt11c2000v + lg-lt11c2000v-top-freezer-refrigerator Derived minimum opening width: 23.625 + 2 x 2 = 27.625 in. Exact-model clearance evidence: Installation Clearance Sides 2"; Installation Clearance Sides 2"; Installation Clearance Sides 2"; Installation Clearance | Sides 2"Open original source ↗ All retained supporting links
Why this value was usedDerived minimum opening width: 23.625 + 2 x 2 = 27.625 in. Exact-model clearance evidence: Installation Clearance Sides 2"; Installation Clearance Sides 2"; Installation Clearance Sides 2"; Installation Clearance | Sides 2" Calculation or inference: width_doors_closed_in + 2 * exact-model installation side clearance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 66.625 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — lg-lt11c2000v-top-freezer-refrigerator LG | Retained specification excerpt: Minimum opening height derived from highest stored appliance endpoint 64.625 in plus documented top | |
Value used by ExactFit66.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceLG measurement source — lg-lt11c2000v-top-freezer-refrigerator Minimum opening height derived from highest stored appliance endpoint 64.625 in plus documented top clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 64.625 in plus documented top clearance 2.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 26.625 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — lg-lt11c2000v-top-freezer-refrigerator LG | Retained specification excerpt: Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 2.0 in. | |
Value used by ExactFit26.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceLG measurement source — lg-lt11c2000v-top-freezer-refrigerator Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 2 in | ✓ Verified — exact model | LG measurement source — lg-lt11c2000v-top-freezer-refrigerator LG | Retained specification excerpt: Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — lg-lt11c2000v-top-freezer-refrigerator Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. WidtOpen original source ↗ Why this value was usedInstallation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. Widt Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 2 in | ✓ Verified — exact model | LG measurement source — lg-lt11c2000v-top-freezer-refrigerator LG | Retained specification excerpt: Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — lg-lt11c2000v-top-freezer-refrigerator Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. WidtOpen original source ↗ Why this value was usedInstallation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. Widt Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — exact model | LG measurement source — lg-lt11c2000v-top-freezer-refrigerator LG | Retained specification excerpt: Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — lg-lt11c2000v-top-freezer-refrigerator Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. WidtOpen original source ↗ Why this value was usedInstallation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. Widt Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — exact model | LG measurement source — lg-lt11c2000v-top-freezer-refrigerator LG | Retained specification excerpt: Explicit rear/back clearance recovered from stored reviewed evidence. Installation Clearance Sides: | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Direct explicit rear/back-clearance value in stored evidence Confidence label: high. Primary evidenceLG measurement source — lg-lt11c2000v-top-freezer-refrigerator Explicit rear/back clearance recovered from stored reviewed evidence. Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. WidtOpen original source ↗ Why this value was usedExplicit rear/back clearance recovered from stored reviewed evidence. Installation Clearance Sides: 2.0 in | ut Handle 1.25" Height to Top of Case 63.62" Height to Top of Door Hinge 64.62" Installation Clearance Sides 2", Top 2", Back 2" Standard Depth No Weight (Unit/Carton) 128lbs. / 139 lbs. Widt Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1 in | ? Verified — finalized database measurement · Calculated/inferred | LG measurement source — 77836549.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit1 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24.625 - 23.625 Confidence label: high. Primary evidenceLG measurement source — 77836549.pdf Exact-model LG specification: Width 23 5/8 in; Width (Door Open 90° with Handle) 24 5/8 in (same without handle). One door: 1 in beside a wall on the hinge side for the door to open to 90°. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model LG specification: Width 23 5/8 in; Width (Door Open 90° with Handle) 24 5/8 in (same without handle). One door: 1 in beside a wall on the hinge side for the door to open to 90°. Calculation or inference: 24.625 - 23.625. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 23.625 in | ✓ Verified — retained secondary source | LG installation document — 77836549.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit23.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836549.pdf Width 23 5/8"Open original source ↗ Why this value was usedWidth 23 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: LT11C2000V. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗files.bbystatic.com · Web source · secondary model/source
Model numbers covered: LT11C2000V. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗LG · Web source · exact model/source
Model numbers covered: LT11C2000V. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
6 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.