This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.875 in | ✓ Conflicting sources — resolved | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Total dimensions width: 35 7/8". Prior 37 3/8" value was Carton Width.Open original source ↗ Why this value was usedTotal dimensions width: 35 7/8". Prior 37 3/8" value was Carton Width. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69 in | ✓ Verified — retained secondary source | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit69 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Height to Top of Case 69"Open original source ↗ Why this value was usedHeight to Top of Case 69" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 70.5 in | ✓ Conflicting sources — resolved | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit70.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Height (Top of Hinge or Door Cap Decor): 70 1/2". Prior 72 5/8" value was Carton Height.Open original source ↗ Why this value was usedHeight (Top of Hinge or Door Cap Decor): 70 1/2". Prior 72 5/8" value was Carton Height. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 32.125 in | ✓ Verified — retained secondary source | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Depth without Door 32 1/8"Open original source ↗ Why this value was usedDepth without Door 32 1/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 33.875 in | ✓ Verified — retained secondary source | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit33.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Depth without Handles 33 7/8"Open original source ↗ Why this value was usedDepth without Handles 33 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 36.3125 in | ✓ Conflicting sources — resolved | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36.3125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Depth with Handles: 36 5/16". Prior 34 15/16" value was Carton Depth.Open original source ↗ Why this value was usedDepth with Handles: 36 5/16". Prior 34 15/16" value was Carton Depth. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 51.3125 in | ✓ Verified — retained secondary source | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit51.3125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Depth (Total with Door Open) 51 5/16"Open original source ↗ Why this value was usedDepth (Total with Door Open) 51 5/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36.125 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.875 + 2 * 0.125 = 36.125 inches Confidence label: medium. Primary evidenceLG measurement source — 104345329.pdf Width 35 7/8"; Installation Clearance: Sides 1/8".Open original source ↗ Why this value was usedWidth 35 7/8"; Installation Clearance: Sides 1/8". Calculation or inference: 35.875 + 2 * 0.125 = 36.125 inches. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.5 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceLG measurement source — 104345329.pdf Minimum opening height derived from highest stored appliance endpoint 70.5 in plus documented top clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 70.5 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 34.125 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit34.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceLG measurement source — 104345329.pdf LG opening envelope: 32.125 + 2.0 = 34.125 in.Open original source ↗ Why this value was usedLG opening envelope: 32.125 + 2.0 = 34.125 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | LG measurement source — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 104345329.pdf Installation Clearance: Sides 1/8". Prior 4 1/16" value was Door Edge Clearance with Handle.Open original source ↗ Why this value was usedInstallation Clearance: Sides 1/8". Prior 4 1/16" value was Door Edge Clearance with Handle. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | LG measurement source — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 104345329.pdf Installation Clearance: Sides 1/8". Prior 4 1/16" value was Door Edge Clearance with Handle.Open original source ↗ Why this value was usedInstallation Clearance: Sides 1/8". Prior 4 1/16" value was Door Edge Clearance with Handle. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | LG measurement source — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 104345329.pdf Installation Clearance | Sides 1/8", Top 1", Back 2" | Carton Dimensions (WxHxD)Open original source ↗ Why this value was usedInstallation Clearance | Sides 1/8", Top 1", Back 2" | Carton Dimensions (WxHxD) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | LG specification record — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG specification record — 104345329.pdf Installation Clearance Sides 1/8", Top 1", Back 2"Open original source ↗ Why this value was usedInstallation Clearance Sides 1/8", Top 1", Back 2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.0625 in | ✓ Verified — retained secondary source | LG measurement source — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit4.0625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceLG measurement source — 104345329.pdf Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Door Edge Clearance with Handle 4 1/16"Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Door Edge Clearance with Handle 4 1/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.875 in | ✓ Conflicting sources — resolved | LG installation document — 104345329.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104345329.pdf Width: 35 7/8". Prior 37 3/8" value was Carton Width.Open original source ↗ Why this value was usedWidth: 35 7/8". Prior 37 3/8" value was Carton Width. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 35.875 in. Earlier retained values: 37.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Total dimensions width: 35 7/8". Prior 37 3/8" value was Carton Width.
View source scope, location, and impact on fitSelected: 70.5 in. Earlier retained values: 72.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Height (Top of Hinge or Door Cap Decor): 70 1/2". Prior 72 5/8" value was Carton Height.
View source scope, location, and impact on fitSelected: 36.3125 in. Earlier retained values: 34.9375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Depth with Handles: 36 5/16". Prior 34 15/16" value was Carton Depth.
View source scope, location, and impact on fitSelected: 35.875 in. Earlier retained values: 37.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Width: 35 7/8". Prior 37 3/8" value was Carton Width.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: LS27T3230S. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
16 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.