This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Top Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-24. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 33 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit33 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Width 33"Open original source ↗ Why this value was usedWidth 33" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit68 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Height to Top of Case 68"Open original source ↗ Why this value was usedHeight to Top of Case 68" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit69 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Height to Top of Door Hinge 69"Open original source ↗ Why this value was usedHeight to Top of Door Hinge 69" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29.5 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Depth without Door 29 1/2"Open original source ↗ Why this value was usedDepth without Door 29 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit34 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Depth without Handles 34"Open original source ↗ Why this value was usedDepth without Handles 34" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 34 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit34 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Depth with Handles 34"Open original source ↗ Why this value was usedDepth with Handles 34" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 63 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit63 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Depth (Total with Door Open) 63"Open original source ↗ Why this value was usedDepth (Total with Door Open) 63" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 37 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 104687241.pdf + LRTLS2403S.pdf + 3e24a5efc0fbdaf924d735e54b2b40f1be37be0fe1aff0687aba15a3ec9eb139 + LRTLS2403S-LG-Builder-Spec-Sheet.pdf d1y6ucal9je0uy.cloudfront.net | Page 1 | |
Value used by ExactFit37 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * exact-model installation side clearance Confidence label: medium. Calculation inputs: Overall width; Primary evidenceLG measurement source — 104687241.pdf + LRTLS2403S.pdf + 3e24a5efc0fbdaf924d735e54b2b40f1be37be0fe1aff0687aba15a3ec9eb139 + LRTLS2403S-LG-Builder-Spec-Sheet.pdf Derived minimum opening width: 33 + 2 x 2 = 37 in. Exact-model clearance evidence: Back, Top and Side Clearance | 2"; Installation Clearance | Sides 2"Open original source ↗ All retained supporting links
Why this value was usedDerived minimum opening width: 33 + 2 x 2 = 37 in. Exact-model clearance evidence: Back, Top and Side Clearance | 2"; Installation Clearance | Sides 2" Calculation or inference: width_doors_closed_in + 2 * exact-model installation side clearance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceLG measurement source — 104687241.pdf Minimum opening height derived from highest stored appliance endpoint 69.0 in plus documented top clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 69.0 in plus documented top clearance 2.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31.5 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceLG measurement source — 104687241.pdf LG opening envelope: 29.5 + 2.0 = 31.5 in.Open original source ↗ Why this value was usedLG opening envelope: 29.5 + 2.0 = 31.5 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 2 in | ✓ Verified — retained secondary source | LG measurement source — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 104687241.pdf Installation Clearance | Sides 2", Top 2", Back 2" | Weight (Unit/Carton)Open original source ↗ Why this value was usedInstallation Clearance | Sides 2", Top 2", Back 2" | Weight (Unit/Carton) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 2 in | ✓ Verified — retained secondary source | LG measurement source — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 104687241.pdf Installation Clearance | Sides 2", Top 2", Back 2" | Weight (Unit/Carton)Open original source ↗ Why this value was usedInstallation Clearance | Sides 2", Top 2", Back 2" | Weight (Unit/Carton) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — retained secondary source | LG measurement source — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 104687241.pdf Installation Clearance | Sides 2", Top 2", Back 2" | Weight (Unit/Carton)Open original source ↗ Why this value was usedInstallation Clearance | Sides 2", Top 2", Back 2" | Weight (Unit/Carton) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | LG specification record — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG specification record — 104687241.pdf Installation Clearance Sides 2", Top 2", Back 2"Open original source ↗ Why this value was usedInstallation Clearance Sides 2", Top 2", Back 2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2 in | ? Verified — finalized database measurement | LG measurement source — 104687241.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 104687241.pdf Door Edge Clearance with Handle 2"; Door Edge Clearance without Handle 2". The door angle is not stated and the value is under 6 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedDoor Edge Clearance with Handle 2"; Door Edge Clearance without Handle 2". The door angle is not stated and the value is under 6 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 33 in | ✓ Verified — retained secondary source | LG installation document — 104687241.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit33 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 104687241.pdf Width 33"Open original source ↗ Why this value was usedWidth 33" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: LRTLS2403S. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗d1y6ucal9je0uy.cloudfront.net · Web source · secondary model/source
Model numbers covered: LRTLS2403S. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-24. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.